Benches Vintage and obsolete

16

Getting Data off of SCSI drives - Syquest…

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I have the Power Mac 8500/120 - is that a G3?

Anyway, those came with CD-ROM only and I want to somehow get all the old data (internal and external Syquest/Jaz) burned onto CDs or better yet - DVDs.

Can I move stuff into an OSX Mac over Ethernet? I've looked but can't figure out how - it used to use TCP/IP in the old days and in OSX it's all different.

I don't want to buy a $150 SCSI to USB adapter unless I have to. I actually bought the Adaptek SCSI to USB only to find out it doesn't support OSX!!!

I guess the question is - what's the shortest path from SCSI HD to CD? I don't think I had CDR software back in OS9.

16 replies

Sign in or join Beachball Help to reply.

  1. 0

    Grant Bennet-Alder

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    7.5.3 and later File Sharing

    Any Mac running 7.5.3 or later (with at least OpenTransport 1.1.2 and AppleShare Chooser extension 3.7.4) can share the files of any Mac running OS 9 or later using built-in File Sharing using IP. What is not supported beyond 10.3 is File Sharing via AppleTalk. In addition, Sharing initiated from your 10.4 or 10.5 Mac to a Mac before OS 9 is not supported directly. So you will have to make the connection from the Older Mac end. Alternatively, you could install "Shareway IP" (a low-cost utility) on the older [than OS 9] Mac and connect from the newer Mac.

    You need an appropriate Ethernet connection, and each Mac must have a similar (but not identical) IP Address. On the 10.4 or 10.5 Mac: You must turn on File Sharing in your 10.4 or later Mac:

    System Preferences > Sharing > Services pane > [X] Personal File Sharing

    and click ( Start )

    Look up the 10.4 or 10.5 Mac's IPv4 Address in System Profiler OR Network Preferences, and write it down for later. It may resemble 192.168.0.6

    On the Older Mac: open the Chooser and select AppleShare. Your 10.4 or 10.5 Mac will NOT appear in the right-hand pane, because it does not speak AppleTalk File Sharing protocol. But do not despair!

    It can speak IP protocol, if you ask it nicely. So click on the "Server IP Address" button on the bottom of the right pane, and enter the IPv4 Address of the 10.4 or 10.5 Mac.

    The login screen that appears is sent to you from the 10.4 or 10.5 Mac. Enter a Username and password that is valid on the 10.4 or 10.5 Mac. Choose the drive(s) you want to mount, if there is a choice, and they will appear on the desktop of the Older Mac as shared Network Drives (Drive Icon with a cable coming out the bottom).

    Drag whatever you like to the newly-mounted drive. It will appear on the 10.4 or later Mac. Try to resist the temptation to drag your whole drive all at once. Move smaller batches in a thoughtful way, and you should have no problems.

    TA23008- Mac OS X 10.4 Tiger: "Connection failed" error when connecting to an AFP server

  2. 0

    BDAqua

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I have the Power Mac 8500/120 - is that a G3?

    Actually it prceded the G3s, it had a PowerPC 604 on it...

    http://www.everymac.com/systems/apple/powermac/stats/powermac8500120.html

    http://support.apple.com/kb/SP386

    Can I move stuff into an OSX Mac over Ethernet?

    Likely, what OS does it have on it?

    Set Appletalk to using TCP/IP, and or Chooser>AppleShare+IP, you can connect to the IP of a newer Mac, or maybe even vice versa.

    Another solution is OpenDoor's $39 Shareway IP, (some OS7, 8, 9 releases had a limited version included)...

    http://www.opendoor.com/shareway/

  3. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks - it's running OS9.

    Set Appletalk to using TCP/IP, and or Chooser>AppleShare+IP, you can connect to the IP of a newer > Mac, or maybe even vice versa.

    Setting that stuff in OS9 is quite confusing to me now - I've forgotten it all. Which would be easier - for the New OSX box (10.5.8) to try to discover the 8500 - or vice versa? Granted, moving lots of stuff over Ethernet would be the slow way to go as opposed to finding a SCSI to USB or Firewire solution... but maybe at no cost other than time.

  4. 0

    BDAqua

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Which would be easier - for the New OSX box (10.5.8) to try to discover the 8500 - or vice versa?

    You first have to give the OS9 Mac an IP in Chooser iirc, then see if the newer Mac can connect.

  5. 0

    Glen Doggett

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Maybe there is a trick to getting file sharing to work between OS X and OS 9, but I never figured out that trick, I could mount a shared volume and drag and drop a file, then the transfer would never complete. I don't know what I was doing wrong and gave up.

    You have a couple of other methods to serve up files from the OS 9 machine, use the built-in web sharing, personal web sharing, then you can access files (maybe make some Stuffit archive files first) from a web browser on the OS X machine. This is kind of clunky, but works okay for a few small archive files maybe.

    Another alternative is to use an (File Transfer Protocol) FTP server on the OS 9 machine and an FTP client on the OS X machine. NCSA Telnet, and BetterTelnet include a rudimentary FTP Server, you can basically turn it on and set up the User and Password and your FTP server is on-line.

    http://www.pure-mac.com/remote.html#bettel

    Use CyberDuck or FileZilla on the Mac OS X side to access files on the FTP server.

    http://cyberduck.ch/

    http://filezilla-project.org/

    (and remember Fetch? still around but no longer free
    http://fetchsoftworks.com/fetch/download/)

    The network lag may be really slow, but you can download all this software for free and try it out on some of your most important files, and see if it's worth the effort to do everything.

  6. 0

    BDAqua

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Good suggestions Glen! 🙂

    I never figured out that trick, I could mount a shared volume and drag and drop a file, then the transfer would never complete

    In 10.4.past .8, it would fail one way but work the other way upto a certain size, 10.4.8/9 & up broke AppleTalk even more, I was shocked to see that somewhere in 10.5.x it was fixed again enough to transfer huge files both ways again. 😉

  7. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Maybe this only confuses me further, but I also found this article.

    http://homepage.mac.com/car1son/os9xnet_nfilesharing.html

    Apparently according to this a "crossover" cable is also needed as opposed to an Ethernet cable.

    My feeble attempt at assigning the 8500 an IP address of 10.0.0.1 and Subnet Mask of 255.255.255.0 did nothing.

    I was shocked to see that somewhere in 10.5.x it was fixed again enough to transfer huge files both ways again.

    This sounds promising...

  8. 0

    BDAqua

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I doubt you need a Crossover Cable, newer Macs can Auto switch/detect.

    Apple products that require an Ethernet crossover cable...

    http://support.apple.com/kb/HT2274

    My feeble attempt at assigning the 8500 an IP address of 10.0.0.1 and Subnet Mask of 255.255.255.0 did nothing.

    What are the IPs of ever other Mac/Router? Likely 10.0.0.1 is a bad choice.

    Check the IP of the Ethernet on the other Mac, make this one ONE number higher in the forth place.

  9. 0

    Glen Doggett

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Just to clarify, if you are using a router, and sharing the internet connection with all your computers, then all the Ethernet wires can be standard cables. You shouldn't need to manually set anything, the router should assign the IP addresses to all the computers connected to it, in the most typical default set up.

    If you do not have a router, and want to directly connect one computer to another computer, the older 8500 computer will require a "crossover" cable.

  10. 0

    Jeff

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Have you considered installing a USB 1.1 PCI card in the 8500? After installation, you'd run the Mac OS 9.1 Update. That would install the USB Support files needed to read/write to a USB flash drive. Since USB 1.1 cards are no longer produced, you'd need to buy a secondhand/pulled one. Another option would be buying a used SCSI CD-R/RW drive, but that might be harder to find. I bought 5 or 6 of them at thrift stores about 5 years ago, when I was still using Macs with SCSI ports.

  11. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    if you are using a router, and sharing the internet connection with all your computers, then all the Ethernet wires can be standard cables. You shouldn't need to manually set anything, the router should assign the IP addresses to all the computers connected to it, in the most typical default set up.

    I'm actually trying this on the desktop via one Ethernet cable - sharing a Dell 2408WFP monitor that has tons of inputs - switching back and forth.

    If you do not have a router, and want to directly connect one computer to another computer, the older 8500 computer will require a "crossover" cable.

    The router I have is in another office, but our house is wired for network - problem there is that would have me move the 8500 to another room to get it on the network, through the router... I could do that - run between rooms and set up another monitor - or

    Will have to see if I can dig up and old crossover adapter or have to go out and buy a crossover cable then.... the 8500 has been in the closet for years - at least it's getting some attention!

  12. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    PCI Card w/USB is a good thought - there are even cheap ones on eBay for $20 shipped. The problem is that they all seem to work for G3 or higher - and it's been established that the 8500 is a pre-G3 box.

  13. 0

    Grant Bennet-Alder

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    7.5.3 and later File Sharing

    Any Mac running 7.5.3 or later (with at least OpenTransport 1.1.2 and AppleShare Chooser extension 3.7.4) can share the files of any Mac running OS 9 or later using built-in File Sharing using IP. What is not supported beyond 10.3 is File Sharing via AppleTalk. In addition, Sharing initiated from your 10.4 or 10.5 Mac to a Mac before OS 9 is not supported directly. So you will have to make the connection from the Older Mac end. Alternatively, you could install "Shareway IP" (a low-cost utility) on the older [than OS 9] Mac and connect from the newer Mac.

    You need an appropriate Ethernet connection, and each Mac must have a similar (but not identical) IP Address. On the 10.4 or 10.5 Mac: You must turn on File Sharing in your 10.4 or later Mac:

    System Preferences > Sharing > Services pane > [X] Personal File Sharing

    and click ( Start )

    Look up the 10.4 or 10.5 Mac's IPv4 Address in System Profiler OR Network Preferences, and write it down for later. It may resemble 192.168.0.6

    On the Older Mac: open the Chooser and select AppleShare. Your 10.4 or 10.5 Mac will NOT appear in the right-hand pane, because it does not speak AppleTalk File Sharing protocol. But do not despair!

    It can speak IP protocol, if you ask it nicely. So click on the "Server IP Address" button on the bottom of the right pane, and enter the IPv4 Address of the 10.4 or 10.5 Mac.

    The login screen that appears is sent to you from the 10.4 or 10.5 Mac. Enter a Username and password that is valid on the 10.4 or 10.5 Mac. Choose the drive(s) you want to mount, if there is a choice, and they will appear on the desktop of the Older Mac as shared Network Drives (Drive Icon with a cable coming out the bottom).

    Drag whatever you like to the newly-mounted drive. It will appear on the 10.4 or later Mac. Try to resist the temptation to drag your whole drive all at once. Move smaller batches in a thoughtful way, and you should have no problems.

    TA23008- Mac OS X 10.4 Tiger: "Connection failed" error when connecting to an AFP server

  14. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks to everyone for all the input - I'll have to revisit it after I have a crossover cable in hand.

  15. 0

    Jeff

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    "
    PCI Card w/USB is a good thought - there are even cheap ones on eBay for $20 shipped. The problem is that they all seem to work for G3 or higher - and it's been established that the 8500 is a pre-G3 box."

    As the owner of a fleet of pre-G3 and G3 Macs, including the 7500, 7600, 8500, etc., my suggestion to install a (now-discontinued)
    USB 1.1 PCI card does work. The current variety of USB 2.0 PCI cards may not, as they are multi-controller by design. As I write this, I'm looking at a folder of photos stored on a USB flash drive, that's plugged into a USB PCI card port in a Power Mac 7500. The 7500 is running OS 8.6, with the USB Support drivers from the Mac OS 9.1 Update. Because the 7500's motherboard is almost identical to the 8500's board (it doesn't support the composite and S-Video outputs featured on the 8500's A/V module), it would be an option for you. After installing the card, you'd want to run the
    Mac OS 9.1 Update. The update installer should detect the presence of a USB card and install the drivers. If shopping eBay, a USB 1.1 card would most likely be a pulled component, since they're no longer manufactured. The cost should be no more than $5, and no more than an additional $5 for shipping.

  16. 0

    igirl1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    my suggestion to install a (now-discontinued) USB 1.1 PCI card does work.<</div>

    Thank you - I just bought the card described below from eBay and hopefully it will work - if not - it's not a great loss at $12 shipped.

    Alternatively, the crossover cable I ordered arrived yesterday - which I may try anyway just to see if I can figure out that as well.

    +2 Port USB 1.1 PCI Card for Macs with PCI Slot+

    +There is no brand name on card.+

    +Has 2 External & 1 Internal USB 1.1 Ports. Requires PCI Slot.+

    +Pulled from working machine runnng OS X 10.4.+

    +This is a Used Card and Guaranteed Not D.O.A.+