Benches Vintage and obsolete

5

Start Fine - nice Boing sound - but Shutdown af...

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

A do a lot of Mac OS free Help and people give me old computer in return.
I do a clean install and give them back to people without computer.

A friend gave me an iMac G3 graphite. It was working fine with os 9.X.
After a while, I decided to install Jaguar.

My First mistake was to forgot to check if the Firmware was upgraded. Probably not.

But even without the firmware, Installation went perfectly.
One in the Register screen, I was in a hurry to leave and a couple of days later, I try to started it again but I only had the green light followed by the standard Boing and then after a 6-10 secondes, it shutdown.

I found this Guide to help me with the Firmware problem
http://guides.macrumors.com/FixingNo_Video_on_iMac_G3_After_Mac_OS_XInstall
I attached an external monitor.

I reset the PRAM,
I check the Battery, ok = 3.1V,
I reset the PMU on motherboard from here http://mrjcd.com/junk/PMU.jpg
I try to boot from CD on OS 9 or 10.2,
I try to boot in sigle mode,
I even tried to boot in target mode with firewire plug into another computer.

So far no luck. Is it a hardware problem that arise at the exact time I installed the Mac OS X ?

Any suggestion

Thank you Franco

5 replies

Sign in or join Beachball Help to reply.

  1. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    You installed Mac OS 10.2 or greater on an iMac G3 and you forgot to update the firmware. Now, your iMac won't display anything on the screen or the screen displays funny things. This occurs on the first boot after the installation. A few folks have reported other problems like difficulty in booting.

    This PDF file that describes several procedures for loading the new firmware. This page is often cited in this forum and is probably the best around:
    http://mrjcd.com/gileskennedy/iMacfirmware_problem_v12.pdf
    Online copy of most of the pdf file:
    http://www.avnr55.dsl.pipex.com/dotcom/panthereatsimac/problemsolver

    A detailed analysis of what caused the display problem and another solution involving holding down the Programmer's button:
    http://www.capecodgraphics.com/pages/macintosh.html

    Getting display screen under Mac OS 9:
    http://www.macosxhints.com/article.php?story=20050218164736471

    Another possible fix for dead-screen G3 iMacs
    http://www.macosxhints.com/article.php?story=20050218164736471&mode=print

    What firmware do you need?
    http://docs.info.apple.com/article.html?artnum=86117

    For iMac 333 MHz, iMac 266 MHz, & iMac 233 MHz, you need to use MAC OS 8.0.
    http://docs.info.apple.com/article.html?artnum=60384

    -------------------------------
    Here are in some other commands that you can do in open firmware.

    Hold down command-option-o-f then poweron your machine. Continue holding until the Open Firmware screen appears.
    #In case you have a cd you don't want. How to eject a cd from the internal cd drive:
    eject cd

    #insert the cd

    mac-boot
    #You will need to quickly press the and hold down the c key.

    In case you act too late, shutdown your machine. Hold down the option key. This will bring up the startup manager. Power on your machine. Click on the dvd image. Click on the arrow icon.

    List of devices:
    devalias

    List of variables
    printenv

    This is a quote from the web:
    Sometimes if volumes don't appear in Startup Manager (what you get when you hold down the Option key at startup), you need to reset the Mac's PRAM, NVRAM, and Open Firmware. Shut down the Mac, then power it up, and before the screen lights up, quickly hold down the Command, Option, P, and R keys, until the Mac has chimed twice more after the powerup chime. Then, before the screen lights up, hold down Command-Option-O-F until the Open Firmware screen appears. Then enter these lines, pressing Return after each one:

    reset-nvram
    set-defaults
    reset-all

    Why set nvram variable? I've had open-firmware based Pegasos PPC and it simply had boot command, so instead of:

    setenv boot-device ud:3,:tbxi

    should be enough to write:

    boot ud:3,:tbxi

  2. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    A thousand Thank you.

    I will work on this tonight and I hope to have a positive result to report !

    Thank you again,

    Franco

  3. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Good luck.

    You should be able to hear the hard drive being accessed during the boot up. This occurs even when the screen is not displaying.

    Robert

  4. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Worked like a charm !

    By reading the links you provide, I was able to bring everything to life.

    Thank you

    Franco

  5. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Superb! Thanks for the star.
    Robert