Benches Uncategorized

14

Dual 867MHz Is now Dual 800MHz After Motherboard Replacement?

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

so i replaced the motherboard on my dual 867MHz G4.

the computer turns on now, and i did a fresh 10.4.11 install...but i noticed that it says "Dual 800" instead of "Dual 867" in my "About This Mac" now. i typed "sysctl hw.cpufrequency" in the terminal and discovered that it is actually running at 800MHz, and not 867MHz.

so why did i lose 67MHz with a new motherboard? it was the correct motherboard...any ideas?

14 replies

Sign in or join Beachball Help to reply.

  1. 0

    Allan Jones

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    What does System Profiler show for the bus speed?

  2. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    under system profiler, i see this:

    Number Of CPUs: 2

    CPU Speed: 800MHz

    L2 Cache (per CPU): 256 KB

    L3 Cache (per CPU): 1 MB

    Memory: 2 GB

    Bus Speed: 133 MHz

  3. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    i zapped the PRAM, and reset the PMU many times. i also re-seated the CPU module. nothing worked.

  4. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    to make things even more strange, i just noticed the CPU module says "1 GHz DP".

    what the?

  5. 0

    Grant Bennet-Alder

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    G4 MDD Processor and bus speeds

    There are two classes of Processors for the Mirrored Drive Doors G4 Macs, and they do not follow the main distinction between the products -- Firewire 400 Vs. Firewire 800.

    In the Mirrored Drive Doors models, processor speed is determined by a combination of the jumpers on the processor modules and the Bus Speed of the system into which the processor is installed.

    • Install a processor intended for a faster Bus speed into a system with a slower Bus speed, and it will be clocked slower and run slower than expected. 133/167 slower.

    • Install a processor intended for a slower bus speed into a system with a faster Bus speed, and it will be clocked faster -- in most cases so fast that it will immediately crash.

    133 MHz Bus speed:

    867 MHz dual w 1 MB cache (each processor) from Fw 400 model

    1.0 GHz single w 1 MB cache from Fw 800 model

    167 MHz Bus speed:

    1.0 GHz dual w 1 MB cache (each processor) from Fw 400 model

    1.25 GHz dual w 2 MB cache (each processor) from Fw 400 model

    1.25 GHz dual w 1 MB cache (each processor) from Fw 800 model

    1.42 GHz dual w 2 MB cache (each processor) from Fw 800 model

    1.25 GHz single w 1 MB cache from "education only" 2003 model

    -compiled from the Power Mac G4 (Mirror/FW800) Service Manual, General Information section.

  6. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    ok, i have this straight now...

    this machine was NOT a dual 867MHz, it was a dual 1GHz. i have so many of these machines around here, i get them confused...

    so this computer went from dual 1GHz to dual 800MHz when i changed the motherboard. the motherboard was a 820-1445-A. so i took out a 820-1445-A, and replaced it with another 820-1445-A, and mysteriously went from a dual 1GHz to a dual 800MHz.

    (i also tried a fresh OSX installation, and that didn't help either. so it's definitely not software related).

  7. 0

    Glen Doggett

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Grant Bennet-Alder wrote:

    ...

    • Install a processor intended for a faster Bus speed into a system with a slower Bus speed, and it will be clocked slower and run slower than expected. 133/167 slower

    ...

    so, maybe this is just a coincidence, but a 1 GHz CPU from a 167 mobo installed in a 133 mobo would operate at a proportional 133/167 bus speed ratio = 800 MHz.

  8. 0

    japamac

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    so, maybe this is just a coincidence

    BINGO!

    We have a winner! 🙂

  9. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    indeed. that does seem to be the case...

    but i'm 100% sure that before i replaced the motherboard, i was running at a full dual 1GHz...and i'm 100% sure that i replaced the motherboard with the exact same one that was in there (i'm looking at them both right now).

    so perhaps this motherboard that was in there was modified somehow to allow the computer to run at 1GHz?

  10. 0

    Grant Bennet-Alder

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    ... Or possibly the reverse -- somebody had a motherboard that was too fast for their processor and modified it to run slower to keep their processor from crashing. Then sold it on eBay.

  11. 0

    japamac

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Or possibly the reverse -- Then sold it on eBay.

    Ohhhh! The plot thickens!

    http://www.hardmac.com/articles/4

    Carefully compare the resistors as pictured in the above article.

  12. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    HOLY CRAP! resistor 676 is gone, just like that mod says!

    below is a picture of the motherboard i took out. as you can see, it's been modded to run at dual 1GHz. my new board has not been modded...so that's the problem! incredible!

    http://www.thebrotherkite.com/stuff/res.jpg

    i can't believe it! thanks so much! so i think i'll do the same mod to the new board, and i should be good to go...

  13. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    ...i guess i just need to be sure there are no other components removed or changed.

  14. 0

    William Downs2

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    i pulled the resistor 676, and it's back to dual 1GHz!

    everything seems good. thanks everyone for all the help!