9 replies
Sign in or join Beachball Help to reply.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Use the tempo slider in the Environment and map the controller to it.
Fox
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Thanks for the response. Could you possibly explain how to go about doing this?
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Open an environment window. Go to the clicks and ports layer.
Create a new : Fader : Specials : Tempo ControlDrag a cable from Input View object to Tempo Control.
Try using the pitch bend on MIDI controller to control the Tempo Control.
Check what input, channel and data byte 1 is for the Tempo Control and match it by using the same from your MIDI Controller.JG
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Ok,
So, so I set up the tempo control in the environment and dragged a cable from input view to the tempo control. When using the pitch bend on my midi control, I can see it affecting the input view. But, I'm confused on how to "check what input, channel and data byte 1 is and match it by using the same from your midi controller." Could you explain this a little more? (At the top of the tempo controller in the environment is the number 117, if this means anything).
Thank you very much for your help (I rarely use the environment). - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Can anyone offer any further assistance with this? It would be very much appreciated.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Don't forget to drag a cable from the tempo fader to the sequencer input.
The number on the tempo fader is the tempo.The input, channel, and data byte 1 would be used if you want to use something other than the pitchbend to control the fader. These are in the inspector on the left (press the letter "I" to show it if it's not there). You have to select the tempo fader, and open the disclosure triangle in the inspector.
Now you will see a list. About halfway down is 'input' - it probably is set for pitchbd so leave it. Under that is Channel: probably set to 1. if the fader changes values when you move the pitch wheel, you're good. If not, you have 16 to choose from until it works.
Under that is -1-: 1 If you were to change the above "pitchbd" to say, control - this would now allow you to open a list right there and assign a different knob or slider on your controller.Try it. Change "pitchbd" to "control" and set the -1-: value to 1 (you'll see in the list that 1=modulation). Now your mod wheel controls the tempo fader.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Ok,
I am able to change the tempo with my midi controller, but when I have a drum loop being looped (using the set locators button so Logic is looping just a single or couple of bars of a loop) and I adjust the tempo with my controller, every time the loop repeats, the tempo reverts back to the original starting tempo. it does NOT do this if I change the tempo manually in logic like normal (the tempo stays at what it has been changed to if done the normal manual way using the mouse and adjusting the bpm at the bottom of the screen).
Any suggestion on how to keep the tempo changed when using a midi controller?
Thanks.Message was edited by: Jack Q
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
u need to record the temp changes
put logic in record mode and all should be fine
doing this should be easier than it is - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
How can anything be easier than it is?