Benches Uncategorized

9

Upgrade eMAc using Kingston 1GB PC3200 40…

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Hello guys

Just want to get some clarifications. Is it possible for me to upgrade my eMac G4 1.25Ghz using kingston 1GB PC3200 400Mhz memory. i have two stick in my collection after upgrading my office pc with higher one.

thanks

9 replies

Sign in or join Beachball Help to reply.

  1. 0

    AOL

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi,

    No. The 1.25GHz eMac requires PC2700 333MHz memory. It will not recognize it.

    -Brian

  2. 0

    rozilee

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks Brian.

    As far as i know, PC3200 is a backward compatible with PC2700. Then what was the issue of whether my eMac will recognized it or not?

    Just to get further clarification.

  3. 0

    AOL

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi,

    PC3200 may or may not work in the eMac. The configuration and density of the chips is different. Even if it were recognized, the wrong RAM type leads to crashes, kernel panics, and other abnormal behaviors.

    Try it if you want to, see what happens. It's not like if you put PC3200 in the RAM slot it will damage the computer itself.

    -Brian

  4. 0

    rozilee

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi Brian, thanks for the advice.

    I've tried to put it into my eMac. My eMac booted as usual but unfortunately it is not recognized as 2GB but 1GB instead (both slots recognized it as PC2700 with 512MB each and not 1GB).

    Please advise.

    Thanks

  5. 0

    AOL

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi,

    The eMac probably can only recognize part of it, since it's not on the same bus/speed as the logic board was designed for.

    -Brian

  6. 0

    Király

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    RAM and eMacs seems to be a "try-it-and-see" thing.

    I know that PC3200 is not officially supported. But my eMac shipped with exactly that, as original equipment supplied by Apple. It says PC3200 right on the chip, yet System Profiler identifies it as PC2700.

  7. 0

    Allan Jones

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    My eMac booted as usual but unfortunately it is not recognized as 2GB but 1GB instead (both slots recognized it as PC2700 with 512MB each and not 1GB).

    That means the RAM is high-density; it's not the speed rating. Our eMac 1.42 has one PC3200 stick that is properly recognized at full capacity. It was ordered from a Mac-savvy RAM online dealer.

  8. 0

    Allan Jones

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I should probably clarify the "high-density" issue. High-density RAM is common in peecees and pack more RAM into fewer components. Example: a high-density RAM module may have only eight black chips; low-density would have 16 for a module of the same capacity.

    When certain high-density RAM modules are installed in a Mac requiring low-density RAM, it shows up as exactly half its rated capacity.

    So that's why it's the RAM density and not its speed )PC3200) that is at play in your situation.

  9. 0

    Matthew Knice

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hello, (Sorry to just come in), BUT,

    I just want to add, that you can get pretty cheap RAM here: http://www.macsales.com

    Also, the 700MHz - Some of the earlier 1GHz eMacs will only work with PC-133 SDRAM. this includes: eMac nVidia 700MHz, ATI 800MHz and ATI 1GHz (Without the USB 2.0). Also PC-133 and PC-200 and 300 RAM Appear different from the pins. PC-133 RAM has 2 notches in the connectors and PC-200 & 300 have only one.

    Regards,

    Your Fellow eMac User,

    Matthew Knice