Benches Uncategorized

7

MiniDV tape imported out of sync

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I am importing a Sony MiniDV Premium 60 Tape (DVM60 / ME)

into Final Cut and it is coming in out of sync, not a lot at first,

but cumulatively it loses sync more and more

The tape plays fine when I watch it directly in my present Sony MiniDV

Camcorder (which is an older model from around 2002)

These MiniDV tapes are from 1998, so perhaps it's

a wear and tear issue, but they've been stored in good conditions

Anyhow, I've tried both the regular NTSC 48KHz Capture Setting

and a customized one with the audio at 32 KHz, but still the same problem

These tapes are from a batch of a dozen tapes that all come in out of sync,

so I'm trying to figure out what the proper preset is, but...

unfortunately I don't have on record what model camera it was

Any guidance is much appreciated, thank you

7 replies

Sign in or join Beachball Help to reply.

  1. 0

    David Harbsmeier

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Check the clip's specs. Chances are the sampling rate isn't exactly where it should be. I've seen several DV tapes from clients recorded in Sony DSR series camcorders that had sampling rates of 47999.1hz or 48001hz.

    To fix, export the audio only as an AIF file at the correct sampling rate, then import the resulting file to sync it up with the video.

    -DH

  2. 0

    hbars

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi Evan!

    Are you using the "capture now" in digitize tool?

    Yes... this is "normal" when you use it for a long time (more then 15min. - in my case!)

    If it´s a sample rate issue, then use David´s tip!

    HBars

  3. 0

    Evan Kreeger1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I exported Audio as both 32 and 44 and it still came

    back into project/sequence out of sync, it ended up

    being 44 frames longer

    Also, I tried importing at standard NTSC DV 44KHz Stereo again

    and I got an error message at end of Capture saying

    "One or more of your clip's items don't match...your audio may

    be out of sync"

    This doesn't happen when I change to 32KHz

    so I assume that's what the tape was shot in?

    Confused, did early MiniDV camcorders (1998) use

    32KHz sampling rates and more recent ones use

    44 KHz?

    Anyhow, I've done Capture Now for entire 60 minute clips,

    perhaps i should log and capture to avoid the sync problem

    Issue still is, even when my customized 32 KHz clips

    come into the same customized 32 KHz sequence, they are out of sync

  4. 0

    Evan Kreeger1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    also just to add, I've tried capturing really short clips

    around 1 minute and still have the same problem,

    also from multiple tapes

    Very perplexed

  5. 0

    David Harbsmeier

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    did early MiniDV camcorders (1998) use

    32KHz sampling rates and more recent ones use

    44 KHz?<<

    No. The DV specification allows for 2 channels of audio at 48khz, 16 bit - OR - 4 channels of audio at 32khz, 12 bit. Some DV camcorders will allow for 4 channel recording, but most don't provide enough inputs to do so.

    I'm not sure where you got the 44khz spec. Possibly thinking of CD audio, perhaps (44.1khz)?

    -DH

  6. 0

    hbars

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Evan, David is right...

    4 audio channels at 32khz ... 44khz... it´s the 1st time for me (only in CD!)

    Is it to difficult to sync it by hand?

    I know it´s not the correct way of doing it... but if your client is an ASAP guy, start working on it!

    HBars

  7. 0

    Evan Kreeger1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hey again,

    Well I'm still having weird sync issues

    With another MiniDV tape from 1998,

    I'll get an error message at end of

    capture when I do NTSC DV 48Khz, although

    the sync looks good

    But when I set a custom setting to NTSC DV 32 KHz

    I won't get an error message after capture and

    the sync WON'T work

    Also, the previous posting had said there used to be

    DV settings at 32 KHz 12-bit w/ 4 channels,

    I don't see how to configure this in Custom Capture settings