Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi,
I have an AGP G4 (You can view my mods below).
Very recently my system started overheating, and freezing up; but it would easily restart. My computer case was free of dust build-up, but I cleaned it anyway. Then I started smelling burning plastic, so I figured the problem was a PSU issue. When I tried to unplug the PSU from the motherboard I discovered the PSU Connector had fused to the motherboard connector. So I pried it loose and found Pins #6, 19 & 20 all burned up. These are red wire, 5 volt pins.
I can report that my rig booted, and all components were working at the time I disconnected the PSU. The PSU fan is working: as are the CPU fans, and the case fan. The only unusual thing I noticed was the heat build-up in the case.
The PSU is a converted ATX unit; converted per [this article|http://www.xlr8yourmac.com/systems/ATXG4_AGP_conversion/G4_AGP_to_ATX_casepg2.htm].
Imported from the Apple Support Forums via the Wayback Machine 🔗
Any ideas on this?
I would be concerned with the wiring mods done to use the ATX PSU. A possible short, possible pin damage, possible cracked connector- these are all possibilities.
BTW, what make of PSU? Some ATX PSUs aren't very well built, and the +5v rail could have developed problems.... Could also be the +5v rail was overloaded. What is the available +5v amperage of the PSU?
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I just had the PSU tested. It is producing right at 5.1 v on the 5 volt rail(20 amps). However, the 12 volt rail into the motherboard is producing over 14 volts. I have no clue what to make of this. Maybe the PSU is trying to dump the overvoltage into the other rails?
I have checked and rechecked the rewiring mod, and I am 100% confident that is correct. The PSU is an [Antec|http://www.antec.com/Believe_it/product.php?id=NTU=](excellent reviews), and it has worked fine for around 9 months.
I've purchased a new motherboard, and I'm researching new PSU's. Anyone ever installed a PSU w/ a 120mm fan. Corsair, and Zalman use this configuration. In the Sawtooth the fan would sit on the same side as the 120mm case fan (which pulls fresh air in). So. the two fans would be working against each other.
Thanks.
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
However, the 12 volt rail into the motherboard is producing over 14 volts.
Sounds hot. Should be 12v ± .1 or .2, not 2.....
The PSU is an Antec(excellent reviews),
Surprised to hear, but not impossible......
In the Sawtooth the fan would sit on the same side as the 120mm case fan (which pulls fresh air in). So. the two fans would be working against each other
Not necessarily. The PSU fan should be an intake, with exhaust being through the grill on the rear of the PSU. Problem with the 120mm fan PSUs is the right angle turn that the air has to make.
A dual fan (push/pull type) gives the best airflow, reduces sound, and works best with the G4 case. My Zumax is a dual fan model.
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Japamac,
You're right about the 120mm fan, the pull air in. Anyway, I checked out your Zumax, it seems like an excellent unit. Did you have to purchase cable extensions for it? If so, what did you get.
Thanks.
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Did you have to purchase cable extensions for it? If so, what did you get.
I went off the deep end, and completely overhauled the wiring harness. The MOBO lead didn't need extended, so I used it with the standard ATX-G4 wire mod. All others, though, completely customized for the hardware I have. It could have worked as is, though.
Imported from the Apple Support Forums via the Wayback Machine 🔗
Jesus Mio Cristo Japamac!
Looks like you could fly the Stealth Bomber with your rig.
Thanks for the peek into your MOD.
Are you pulling in air; or exhausting air with the top, front fan?
Take care,
medinaray
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi-
The top is exhaust. The Thermaltake case fan is higher CFM, so I decided to take some heat out to help keep the PSU cooler.
I have some real heat producing parts inside, but all runs nice and cool.
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hello Japamac,
Did you do a Molex to 15 conversion for your SATA hard drives? If so, did you use an adapter, or did you rewire? If you rewired do you have a tutorial?
I've read that the adapters don't supply enough power?
Take care,
medinaray
0
Apple Support Community member·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi Medinaray-
I've read that the adapters don't supply enough power?
That may be because the adapter (and all older PSU's) don't supply the +3.3v. This is inconsequential, as SATA drives still don't use +3.3v.
I initially ran with the Molex to 15 pin adapters (OEM PSU). No problems, just bulk and excess wire, which +I despise+ !! When I changed the PSU, the PSU had dedicated SATA power leads. I still rewired them.
No tutorial (probably should). I just used available pinouts, and carefully pressed onward.
You can change any standard 4 wire Molex to a 15 pin SATA using something like This. Crimp style are also available.