Pull Apart Guide for TAM???
apple Verified ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
G'day,
My TAM needs some repairs.
As those who know may recall, only about 5 Apple repair agents worldwide ever underwent training in repairing the TAM.
Although a pdf version of the manual (user manual that came with the TAM) can be easily found online, I've never come across the actual pull-apart guide for the TAM.
I'm wondering...
a) Does anyone know where I might locate the pull apart?
b) Is it at all possibly Apple might give me a copy?
c) Would it be likely that my local (Australian) Apple repairer would be able to get the pull-part guide if I can't locate it myself?
cheers
cosmic
13 replies
Sign in or join Beachball Help to reply.
- 0
Grant Bennet-Alder ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
The motherboard for the Twentieth Anniversary Mac is a faster "twin" of the slide-out board in a 5500 or 6500, with a different end rail. The end deep inside the machine uses an enormous card-edge connector through which every signal of consequence passes.
The solution to many of the problems of those other Macs is to slide out the motherboard and re-insert it a few times. If that does not clean enough corrosion, then slide out the motherboard and very gently shine up the gold edge fingers with a soft white eraser. Be gentle, because the gold is very thin and it is possible to scrub it off and ruin the board. Do not touch the contacts with your (oily) fingers.
The 4.5 Volt black cube battery, Ray-O-Vac 840, 841 or equivalent should be replaced if its voltage is getting low. Some other Macs use a threshold of 3.2 Volts for replacement.
- 0
John Helock ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I have never come across a take apart manual for the TAM. It is not that hard, however. Start by removing the screws under the speaker covers and go from there. There are many screws to remove, but if you take your time it can be done. I have done it on 2 units recently without a manual and have had great success.
- 0
Jeff ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
For a while, there were numerous web sites that had made Apple's service manuals available for download. Because they had no legal right to do so (Apple's intellectual property), the offenders were sent cease and desist orders for removal of them. Respecting Apple's position on the matter, it would be inappropriate to provide links to any remaining web sources for those manuals.
- 0
Texas Mac Man ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Contact your nearest Mac Users Group
http://www.australian.macusersgroup.org/index.php?option=com_wrapper&Itemid=55 Someone may have the info you need. Cheers, Tom 😉
- 0
Grant Bennet-Alder ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Don't get your hopes up.
The only manual I have seen that claims to be the Service Source Manual has 24 pages of specifications and port identification info appended to the (350-page) user manual. Not so much as an exploded diagram.
Good luck.
- 0
cosmichobo ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I do appreciate that it's Apple's intellectual property... I have no desire to earn money from it like some people do by selling them on eBay (I've reported people to eBay when I see that)... I just really would like to be able to try and fix my TAM... it hasn't worked properly for ages and needs to be opened up, but without a guide I'd hate to try it myself.
As the TAM wasn't sold in Australia at all, it's not like any Apple repairers here are going to know what to do with one. Maybe they will be able to get hold of the manual if I take it to them... I just don't really know any trustworthy repairers in my area, considering that it's not "just any Mac".
Is there an email address I can use to try and ask someone at Apple about this?
Message was edited by: cosmichobo
- 0
Niteshooter ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
As Grant states, there might not be a service manual out there that has take apart information. Yeah that sounds kind of dumb but the 'service manual' I've seen from service source is only a specification guide no take apart.
Have you tried contacting Apple directly to see if they can point you to a shop there?
Guess the other real headache is that the parts are so proprietary to this computer that parts are going to be a real challenge to find especially in a market that it was never sold in.......
Kevin
- 0
Grant Bennet-Alder ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
The motherboard for the Twentieth Anniversary Mac is a faster "twin" of the slide-out board in a 5500 or 6500, with a different end rail. The end deep inside the machine uses an enormous card-edge connector through which every signal of consequence passes.
The solution to many of the problems of those other Macs is to slide out the motherboard and re-insert it a few times. If that does not clean enough corrosion, then slide out the motherboard and very gently shine up the gold edge fingers with a soft white eraser. Be gentle, because the gold is very thin and it is possible to scrub it off and ruin the board. Do not touch the contacts with your (oily) fingers.
The 4.5 Volt black cube battery, Ray-O-Vac 840, 841 or equivalent should be replaced if its voltage is getting low. Some other Macs use a threshold of 3.2 Volts for replacement.
- 0
John Helock ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I have never come across a take apart manual for the TAM. It is not that hard, however. Start by removing the screws under the speaker covers and go from there. There are many screws to remove, but if you take your time it can be done. I have done it on 2 units recently without a manual and have had great success.
- 0
cosmichobo ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi Grant, and thanks for your post,
I was SO pleased in 1998 when I was able to procure my TAM in the 2nd (and final) week of the "firesale". Used it solidly for 8 years before buying this eMac.
Even at that time though, the floppy was dead, and the CD starting to "fail" when reading.
Now, the external SCSI doesn't work (and as the CD is SCSI too, I don't know if it's at fault as well), the USB PCI card I was using doesn't respond, and sometimes during startup it gets a fatal error as well.
Beyond those things (which I've been told I should try opening up and pulling off/putting back the SCSI cables), I'd love to get my hands on a PAL TV tuner card, so that my TAM could finally operate "properly" here in Australia as a multimedia centre.
I do have a pictorial guide to pulling the TAM apart from a guy who posted it online a few years ago, and also know a guy who is an Apple tech, and has opened his TAM (but he's in the USA), so I could probably give it a go... I just would much rather have THE proper guide - just in case...
I guess at this point I'll wait until I can buy:
New Hard Drive
PAL TV card
Sonnet/Newer G4 L2 Cache card
2 x 64MB RAMThen I'll go ahead and open her up and do it all in one go...
- 0
Niteshooter ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
You may want to clean the lens on your CD for some reason folks don't/won't do this simple fix.
Kevin
- 0
cosmichobo ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
🙂
I did try that... a few times... using the cd-with-brush type things, and just a lens cleaner spray and cloth.. didn't fix the problem sadly.
I have 2 SCSI CD drives that I can try to use externally, but because the SCSI port isn't working, that option is out as well. Ultimately I would prefer to get a new internal drive...
- 0
cosmichobo ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I gave up waiting, and opened up my TAM recently.
http://www.youtube.com/watch?v=A0EcK-d1dPU
Anyone wanting more info, please get in touch with me and I'll give you as much help as I can.