Power supply upgrade
apple Verified ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Is it possible to upgrade/increase the power supply on my Sawtooth?
If it is, and soldering is required, are there instructions?
Japamac, I'm hoping you weigh in on this one....it seems you've upgraded your power supply.
8 replies
Sign in or join Beachball Help to reply.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi-
Yes, it's very possible...
As for soldering, yes, a little, buy it's only a couple of wires.
Use the explanation on this page. FrankenMac offers some nice explanations.
Some ATX PSU motherboard connectors are a bit short. Even if the length is adequate, using an extender to make your mod's to provides peace of mind, in case you are a little nervous.
In the end, though, the extender is a bit bulky, so, as possible, get a PSU with adequate length, and mod the PSU wires to keep things clean.Using the extender for practice, though, is a good way to go.....
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Thank you for the help and advice. I'm looking at your links, and will go from there.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
You're welcome!
Let me know if you need further help. It's pretty straight forward.
BTW, a PSU of around 500W is plenty. - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hello Japamac
The soldering piece for this ATX upgrade is simple.
But, I've found many PSU's out there. There's Apevia, Thermaltake, OCZ, LOGISYS, Corsair, Rosewill, etc. None of these have a power out receptacle like the stock Delta on the Sawtooth, and that's OK, I can plug the monitor into a strip.Is a 20 + 4 pin connector OK? I'm not seeing any that are just 20 pin. If I'm understanding the 20 + 4 correctly, it will work both ways?
Do all ATX brands rewire per the xlr8yourmac schematic on the link you provided?
Will dual fans suffice?
Finally, are the dimension W 150mm x H 86mm x L 140mm OK for the Sawtooth? These dimensions seem to be universal. - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Yep, lotsa' different PSU's....
Use the list on the linked page to guide your purchase. Seasonic, Corsair, Enermax and Antec are excellent choices (all really expensive here in Japan....). Zalman and Thermaltake are also reliable makers.Yes, many are 24, and some are 20+4. So, get a PSU that has the 20+4 connector. You don't need the "+4", just the 20 (push the 4 pin connector aside). Everything will be great.... The 20 part of the 20+4 is the same as a 20 from the old ATX standard.
Dual fans, single fans, either is fine. Stick with a dual 80mm or 80mm+90mm (mine has the later) in the dual fan setup. The single 120mm units aren't really good for the Mac G4 case..... A dual "push pull" setup is usually quietest, and cools efficiently. Don't get too wrapped up in it, as the PSU technology greatly exceeds the needs of the G4. Usually, a more "basic" model, and some of the above makers older models are the best candidates.
And, yes, one has to give up on the monitor recep. Not such a problem, though. Like you said, just need an open spot on the power strip.....
And, finally, ATX PSU's are all the same size (+/- a mm or two). The PSU's in the G4's up to the QS are all ATX based, so it's pretty much slide in, slide out. Some PSU's are designed for upright, some horizontal (the later are quite common). Horizontals usually have a 120MM fan (or two) and can be used in the upright position, but a more traditional upright version would make better sense in the G4.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
.....Excellent!
Thank you for the useful, and helpful info.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi japamac
What happens with the other two pins in the cable on the factory included power supplies? Mine is a G4 Digital Audio, but I suppose all Power Macs power supplies come with the same 22 pin connector. - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi-
Sawtooth's used 20 pin connectors. Gigabit Ethernet and Digital Audio use 22 pin. Quicksilvers use 22 pins, but different from the GE and DA. MDD's use 24 pins.
The supplied voltages are where the differences lie. Checking the Frankenmac link in my post above will show you what the differences are in the pins and supplied voltages.
This discussion describes the process for adapting an ATX PSU to a DA G4.