Benches Uncategorized

8

You must connect using Firewire to restor…

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Alright folks;

I consider myself quite savvy when it comes to all things digital, but I am officially befuddled. I own a third gen iPod (touchwheel) that was purchased back in early '04. It has collected dust over the past two years, but I finally ordered a replacement battery, swapped out the old one, and got it running again. I hooked it up to my 17 inch iMac (intel) and iTunes detected it just fine (synced songs to it, listened to them, etc.). It was originally purchased as "Windows formatted" and I wanted to restore it to "Mac formatted"--this was the only way to update it. During the restore process, it errored out and jacked up my iPod. I should have written the error message, but didn't think to at the time. Anyway, the restore process basically froze and I had to force quit iTunes. Now, when I look at the iPod I get an Apple logo...

After spending the last 24 hours trying the 5R's, putting the thing in "disk mode", googling everywhere, and searching this forum, I am at a loss. I even resorted to re-installing the OS and updating all of my software. Now, when I place the iPod in disk mode iTunes sees it, but when I try to restore it I get the following error message: You must connect using Firewire to restore the ipod "ipod". Hmmm, let's think about this: Firewire charges the iPod only, correct? Correct. USB 2.0 syncs data via iTunes, gets updates etc. Anyway, holding on to my last thread of hope, I tried hooking it up via FW and nothing, other than charging, happened.

Note: I also manually downloaded the updater package and it only gives me an option to update my iPod (which doesn't work because the software on the iPod is jacked up). The restore option is grayed out because--guess what? It says I have to hook it up via FW! Please excuse the sarcasm.

So I recently called Apple support and the tech told me that it's most likely a combination of outdated hardware and the software update. I tried to refrain from telling him what
I thought, but I eventually blurted out, "Apples f*@(%$ up software broke my iPod. It worked fine before I tried to restore it. I had synced music to it and everything." The tech froze up and then said the hard drive was probably old and crashed. Where do they get these people? Now my iPod is hosed, and it looks like Apple is extorting through shoddy software updates. Thanks for breaking my iPod, Apple.

Lesson is: Don't update or restore your iPods!

Somebody...help!

Thanks, D

Message was edited by: D-Rock '82

8 replies

Sign in or join Beachball Help to reply.

  1. 0

    kuching

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Are you are using USB you will get an error message? If so, switch to firewire. 3rd generation iPods use a firewire, not USB connection.

  2. 0

    D-Rock '82

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    When I connect via firewire it only chargers the ipod. It doesn't recognize the ipod in iTunes when connected via Firewire. Only when I connect it via USB 2.0 does it recognize the ipod in iTunes and give me the option to restore.

  3. 0

    Fourth

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hello,

    I had this exact same problem! I thought I was the only one. My 3rd gen has always only charged with FW and connnected w/ USB, but someone, like the reply above, has told me 3rd gens are supposed to only connect w/ FW. Nope, not mine. Mine was originally windows formatted too, but I've been using it with Macs for a while. Maybe that's why it'll only connnect with USB, since PCs don't usually have FW ports. But I can't reformat it for Mac now, because like you I have no way to connect it! Let's keep in touch if either of us finds a solution to this?

    Good Luck.

  4. 0

    PT

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    First thing I would do is confirm your Firewire ports are still working and not latched up. Do you have other Firewire devices and if so are they working ok?
    If you don't have other firewire devices, go to the Apple menu and get to the System Profile and check and see if the Firewire bus shows up normally or if it shows up blank there.
    Patrick

  5. 0

    IdrisSeabright

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    The vintage iPod you talking about did, in fact, sync using Firewire. You might check to see if you have the original cables. At some point, iPods came with both Firewire (for connecting to a Mac) and USB (for connecting to a PC). If you have the original Firewire cable, it may solve your problem.

    Some of the older iPods also that, in order to finish the restore process, you hook it up to an AC charger. Because of that, the older iPods included an AC charger.

  6. 0

    D-Rock '82

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi,

    Thanks for replying; I'm glad I'm not the only one experiencing this issue. I recall using firewire to connect my iPod to my G4 Powerbook back in '03-'04. Unfortunately, I lost the original cables after two moves (I'm in the military), so I bought the ReTrak cables which included both USB 2.0 and FW. My FW port is fine because I have a 300 GB FW external hard drive attached to my iMac, and it works. What's strange is that before I tried to update it, the iPod worked fine when connected via USB 2.0. Once I tried updating it, the update froze up and my iPod displayed an . As explained in my first post, I've exhausted all efforts to get this thing working again. I appreciate everyone's responses. Fourth, please let me know if you find any fixes.

    Thanks, Derek

  7. 0

    D-Rock '82

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi Meg,

    I noticed Apple sells a FW to dock connector for my iPod (like the one I used to use). Here's the URL:
    http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=EA2 FF613&fnode=home/shopipod/ipod_accessories/cablesdocks&nplm=M9127G/B

    I may drop the 20 bucks to test it out. I already purchased a Shuffle as a replacement, but it would be nice to get my older iPod working again.

    Thanks for your advice, Derek

    Message was edited by: D-Rock '82

  8. 0

    IdrisSeabright

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    It looks like the right cable and the text indicates it should work.

    Best of luck.