Benches Uncategorized

7

Upgrading eMac RAM, do I have to use matched pa...

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I have a E mac G4,( Combo) running 80 Gig hard drive, it originally came with 128 MG Ram and I had an additional 256 which increased its memory to 384. With leopard coming I need minimum 512 so I have ordered a 512 compatible memory133U Sdram. What I was wondering, was I will have a 512 and if I pull
the original 128 and leave the 256,I would have 768 which is above the listed minimum.( Which is all I can get right now)
Is there a recommended configuration or does it matter what slots these Ram occupy( Of course in a perfect world you'd have matched sets ) But this is not a perfect world.
So is there a recommended configuration and if so what would it be.
Also when you start up if you leave the 256 in place and run I believe hardware will it be necessary to start from the start up disk to get The HArdware utility disk?Or will it recognize the new Ram.
And where is that located( Disk) ? Since this is the first time I have changed ram.

7 replies

Sign in or join Beachball Help to reply.

  1. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Yes, if you leave the 256 MB module in and add the 512 MB module you will have a total of 768 MBs of RAM. Although this will exceed the minimum requirement you would find Leopard will run better with more RAM. Ideally you should put the maximum amount of RAM in that your model supports.

    There is no special configuration required. The RAM is recognized automatically. There is nothing you need do other than install it.

    Also when you start up if you leave the 256 in place and run I believe hardware will it be necessary to start from the start up disk to get The HArdware utility disk?Or will it recognize the new Ram. And where is that located( Disk) ? Since this is the first time I have changed ram.

    I'm sorry but the above is virtually unintelligible. What exactly are you asking. Please be clear.

  2. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi John

    Welcome to discussions.

    Is there a recommended configuration or does it matter what slots these Ram occupy

    No, it does not matter, not with eMacs at least which are tough machines, not fussy in the least about RAM, of which slot one or two either way will work.
    Example of their flexibility:
    http://discussions.apple.com/thread.jspa?threadID=1176972

    will it be necessary to start from the start up disk to get The Hardware utility disk? Or will it recognize the new Ram.

    It will recognize the new RAM no hardware setup requireed. Swap the old RAM out, and replace it with the new. Just make sure you insert the RAM correct side up as it can only go in one way. Check the old one that comes out to notice where the notch is.
    Gently but firmly push it in all the way home so that it seats in correctly and that the clips lock back over so they are flat. Start up the machine and it should immediately recognize the additional RAM. No disk needed.

    tip: lay a towel on the desk and lower the face on the eMac down onto it, to prevent scratching its front.

    regards roam

  3. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Well my question is answered, HOwever it had to do with configuration, Some require a special set up or matched pairs.Or if the configuration had required say and ascending order, 256 then 512.

    But since it doesn't matter the question is irrelevant( Thanks)

  4. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I understand. That is not a concern for your model. It does not use dual-channel RAM nor require matched pairs.

  5. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi John,

    First of all, Welcome to the  Discussions Forums!

    Just thought I'd post a link to the:

    eMac: How to Install or Replace Memory

    Apple Knowledge Base Article for when you decide to install the new memory.

    good luck,

    littleshoulders

  6. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I have a G5 iMac that I just purchased a RAM upgrade from 256K to 1M. When I installed the new ram, the computer just beeped and then the power light flashes three times, pauses, flashes three times, pauses, etc. Any ideas on what may be the problem?

    Thanks!
    Greg Stout

  7. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    +I have a G5 iMac that I just purchased a RAM upgrade from 256K to 1M. When I installed the new ram, the computer just beeped and then the power light flashes three times, pauses, flashes three times, pauses, etc. Any ideas on what may be the problem?+

    Thanks!
    +Greg Stou+t

    It's some of your memory that's bad. I had the same problem with some new ram that worked for a couple of hours then locked the system. Swapped a mix between the old and new ram and found that one of the new modules was bad and locks the system up any time it's in the computer. Need to replace that module. This is documented elsewhere. The three clicks/flashes is the giveaway.