Benches Printing and scanning

3

Canon MP560 won’t “add printer&rdqu...

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Hi, all, and especially PaHu!

I have also “lost” my MP560 as a wireless printer since the last software update.

I have two machines: a desktop iMac and a Macbook Air, both running Snow Leopard, and up to date - almost (I’ll come to that). My Wifi network is created by a Time Capsule, to which the iMac is attached by ethernet.

The MP560 stands alone, connected only by by WiFi.

On the Air, I saw “Canon Printer Drivers” (version 2.3, IIRC) in Software Update, so I installed it. I haven’t installed that update on the iMac (thank goodness...)

On the iMac, the MP560 is fully functional as a wireless printer and scanner; it’s in my printers list, and it appears via Bonjour (eg after a few seconds) in “Image Capture” as a scanner when I start Image Capture.

After installing the update, wireless printing from the Air stopped working. Initially, it showed the printer (with a Mac address) in the printer list, but simply said “printing” without anything happening. So, I thought deleting the printer and re-adding it might encourage the new drivers to work. Once I did that, I couldn’t see it to add any more.

So, then I downloaded and installed the very latest drivers and IJ network utility from Canon, and installed and ran them. I even used the IJ tool to “set up” the printer again, for network use, but connected via a USB cable temporarily (you used to have to set up Canon wireless printers via USB to get them configured for the wireless network, though these days you can do all the wireless setup up via the screen on the printer itself.). What I now have is the MP560 installed as a printer, but “offline”, which means that its no longer connected via USB.

When I go to “add printers - more printers - Canon IJ Networking” I can see the MP560 in the list, with a MAC address, which means it’s being seen as a wireless device, but it is described as an “unsupported printer” and I can’t add it.

Which is very frustrating, given that it has been added on the Air as a USB printer, and the same printer is working fine as wireless printer on the other iMac, and WAS working fine on the Air before the so-called software upgrade...

Anyone got any ideas?

best regards,
Matt

3 replies

Sign in or join Beachball Help to reply.

  1. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    OK... for anyone else reading this:

    I read in another thread (about a Xerox printer with a similar sounding problem) that you can "reset the printing system".

    You do it by going to the "Print and Fax" pane of the system preferences, and CTRL-clicking into the panel at the left that would normally show installed printers. In my case it was empty.

    After I'd done that, and the beach-ball had spun for a minute or so, the MP560 showed up as a Bonjour Scanner, and then when I clicked "+" to add a printer, then "more printers" and then selected "Canon IJ Networking", I could choose the MP560 - it was no longer an "unsupported printer."

    So, if you're struggling with a similar sounding problem after upgrading the Canon software through software update, I'd try resetting the printer system first. Then if that doesn't work, I'd download the latest CUPS driver from the Canon web site and try again. And finally, if THAT doesn't work, I'd download the Canon MP Software installer from the Canon website as well, run it, set up the printer again, and THEN reset the printer system again...

    bestest,
    M.

    Message was edited by: Matt Bacon1

  2. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Matt - Just saw your post describing the reset of the printing system. Tried it out and it worked famously! Thank you so much!

    San Diego Beth

  3. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hello Matt,

    Good to read you got it working. The reset printing system is often the savior of many printing problems. It is also very helpful after installing a driver update as you have experienced.

    Just one thing I want to comment on, especially for the sake of others who may read your solution.

    The v10.30 Canon printer driver is not designed to work with the Canon IJ Network utility. I and other Canon owners have found that the printer queue can become unstable if you add the network printer driver using the More Printers > Canon IJ Network.

    To add the Canon network printer, you should only use the Default browser view of Add Printer. When you do this, you will see the Canon AIO scanner immediately, with the Kind column showing 'Bonjour Scanner'. And if you wait several more seconds, the Canon AIO printer will also appear, with the Kind column showing 'canonijnetwork'. Select this entry to add the printer and the other to add the scanner. This should be the only procedure you follow to add the networked Canon AIO on OS X 10.6.

    Pahu