Imported from the Apple Support Forums via the Wayback Machine 🔗
I am experiencing mid/high pitch crackling during audio playback when outputting through a firewire DV deck. Audio is played back at the right speed and is of high quality, except for the crackling that appears to be mixed in with the signal. If i switch off the video output in the preferences and route through the soundcard the audio is fine, suggesting that all there is no fault with the actual audio clips.
I have tried 4 different DV devices, including a simple firewire digi/analog converter box. I have tried monitoring directly through headphones on the DV deck, different mixers/speakers etc - i get the same results every time.
My project is as follows...
PAL DV 720x576 - Firewire out is set up using this option
48Khz 16bit
25fps
Any suggestions?
I would simply monitor from the computer soundcard but this isn't possible while outputting to firewire - another annoying issue!
Imported from the Apple Support Forums via the Wayback Machine 🔗
Are the audio source files stored on an internal drive, or an external firewire drive?
0
monkeytennsi·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Thanks for your reply...
All audio and video is stored on internal drives, I am not sharing the firewire bus with any other devices and I've tried using both firewire ports.
0
D Gilmore·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Is your media on a dedicated internal media drive or is it on your system drive?
If it's on your system drive then that could be an issue.
Did you try swapping out different firewire cables? It might also be as simple as that.
Do you have more than one device connected to your computer through firewire?
0
audiopablo·
Imported from the Apple Support Forums via the Wayback Machine 🔗
This sounds like a "buffer size" problem. I can't for the life of me find it in STP2 - I only just got it a few days ago. It's easy to find in the audio preferences of logic, though. You might have a look see if there's a control panel for your device. This problem comes up often on the PC side of the world and this is a common solution. I don't know if this is your problem, but it is worth a shot.
0
monkeytennsi·
Imported from the Apple Support Forums via the Wayback Machine 🔗
The audio is on the system drive, but a brand new 500GB SATA drive on a top spec MacPro really shouldn't have trouble keeping up. This happens with just a single track of audio also, the data rate required of the hard drive to play back a single track really can't be very much. The problem only occurs when playing through firewire so i very much doubt the hard drive is an issue.
I've replaced cables, decks etc to no avail. There are no other devices using the firewire bus.
0
monkeytennsi·
Imported from the Apple Support Forums via the Wayback Machine 🔗
That could be it, something else has shown up now as well, sometimes the audio plays at a higher pitch a bit like a chipmunk! From my experience of logic it does sound like it could be an audio buffer issue i'm hearing in STP, hard to be sure though. The audio options are very limited in STP unfortunately, it's supposed to just 'work', which is fine until it stops working!
0
fraser135·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I'm having the same problem. I've been doing this work for 8 years now and have never seen a problem like this. When I bring the audio in analog there is no popping. I have a Sony V1U and am downconverting to DV. Everything is setup perfect on the camera and in FCP 6. The audio levels are perfect. Every one of my clips that is brought in through firewire has this issue.
0
monkeytennsi·
Imported from the Apple Support Forums via the Wayback Machine 🔗
i'm not sure this is the same issue. are your files popping when played OUT firewire through soundtrack? or have you get pops on your actual audio data that show up through your mac audio output?
in my case the audio data is fine, it's only crackles/pops that i can hear when outputting through firewire. if i could just choose to output video via firewire and not audio i'm sure this could be solved.
0
zmeyer·
Imported from the Apple Support Forums via the Wayback Machine 🔗
10.4.10 and 10.4.11 and ESPECIALLY 10.5.x introduced some questionable firewire audio drivers into the OS. If you can, revert to 10.4.9 and your problem might go away. That's the answer I got straight from my firewire audio device's manufacturer.