Benches Networking

11

HP Printer Error- the process "usb" stopped une...

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I just had my database need to be rebuilt and now I can't seem to print with my HP printer. I get the message the process "usb" stopped unexpectedly with status 233. I know the printer is connected as I ran utilities and can print a test page from the computer. What do I need to do? Thanks for your help.

11 replies

Sign in or join Beachball Help to reply.

  1. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Your best bet is to contact HP. I suspect that error code is one of theirs and not an Apple code. I've had pretty good luck with contacting HP for troubleshooting. Even their online help system is not too bad.

    I noticed your equipment line says "iMac G3" but you posted in the eMac G4 forums. If the question is about an eMac, please post the specs. Might save some back-and-forth asking about them.

    I assume the printer worked OK on your computer before the maintenance?

    What utility did you use to "repair the Database?"

  2. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Sorry, yes it is an emac. The printer was working fine yesterday. I used the Database Utility in Office as there was some issues with my entourage. The online help for HP does not support MAC, so I will have to wait till tomorrow to call them. I imagine I will need to uninstall and reinstall something. Perhaps the printer drive, but not sure.

  3. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    The online help for HP does not support MAC

    I'm finding Macintosh Support on the HP site, and from a Mac. If you are having trouble with that site, post the exact model and number for your printer and I'll be glad to research for you later tonight. HP printers have a "family name (like Deskjet; PhotoSmart, etc) and usually a number (example:we have a PhotoSmart C6280) that are both needed for a good support search.

  4. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Yes it is a photosmart C6380 all in one...Thanks

  5. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Morn'n Goldie
    Just happen to have the HP MAC support bookmarked. Here's the HP address regarding drivers and software for your All-in-One HP. Did the database need to be rebuilt?

    http://h10025.www1.hp.com/ewfrf/wc/softwareList?os=219&lc=en&dlc=en&cc=us&produc t=3560280

    Did you come to resolution on the external hd?

    Happy N Y
    Scott'so

  6. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Working on the external HD.

    Yes rebuilt the database. That is what is causing the problem.
    Tried to call tech support, but no one avail now.

  7. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Yes it is a photosmart C6380 all in one

    You are lucky. That model gives you an option not offered on cheaper printers.

    You could abandon the USB connection completely and use ethernet to print. That model has, in addition to USB, an ethernet (or "network") port and wireless connectivity. Wireless can be flaky but ethernet is an amazing way to print--faster and more stable that using USB. The port should should be just above or below the USB port.

    If your computer is already connected to the internet via ethernet, you can get an inexpensive ethernet router to create enough ports. The router goes between your modem and the computer gear. One router port is usually marked "WAN" and is where you connect an ethernet cable going from the modem. The router will have several other ports marked "LAN" that those connect yo you computer equipment.

    You are basically splitting one ethernet line into several. If you have only the iMac and the HP printer, each one would connect to its own LAN port and you can print without USB issues. Normally setting up a wired router takes no software and no tweaking on your part. You connect the wires and it's running.

    Here's a start on learning about home networking. In teh picture, what's labeled "gateway" is the router.

    http://en.wikipedia.org/wiki/Home_network

  8. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I hesitate to add to Allan's and Scott'so's advice, since their's addresses specific details and is more likely to be valid, but for what it's worth, two practices I've picked up using HP printers for 20+ years that I find worth applying blindly:
    -- always check the HP website for your specific model for updated software if you used the installer that came with the printer or AIO (I can't recall ever getting an HP printer or AIO that didn't have a more recent version of it's software online compared to the shipped disc). Even if the software you had was running well before, check if there's an update.
    -- any time I install or reinstall HP software, I automatically and immediately use Disk Utility to run Repair Permissions on the hard drive. HP's actually gotten better about this in recent years, but their installers have a history of trampling System file permissions (running Repair permissions after any third-party installer that asks for an administrative password can't hurt)

    On the Office end, do you have all updates installed for your version of Office? You can use the "check for Updates" option in the Help menu of any of the main Office programs. If there is an update, try installing and then re-run the Database Utility.

  9. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    JMVP wrote;

    always check the HP website for your specific model for updated software

    Oops! Something I always do but forgot to mention. Thanks for remembering!

    A

  10. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks Allan, will look into that ethernet option. Sounds easy enough. Thanks

  11. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Did you have success?