Adding Samsung BluRay Player to Airport Exteme ...
apple Verified ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Has anyone worked through this?
I just bought an Airport Extreme and had few problems setting it up. When I tried to connect with my Samsung Blu-ray player it does not connect although it does get as far as recognizing the Airport Extreme network (both the main network and guest network). I write in the password and it does not connect.
Any ideas?
7 replies
Sign in or join Beachball Help to reply.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
WaterCons, welcome to the discussions!
The likely cause of your connection issue with the Samsung player is a Radio Mode or Security compatibility issue.
Open AirPort Utility, which you used to configure the Extreme, and click on Manual Setup.
Click the Wireless tab just below the row of icons at the top of the pane to display the page for your wireless settings.
Do you know what type of wireless device the Samsung will support? It may not support faster speed "n" networks, so check that the Radio Mode for the network that you are using is set for 802.11n (802.11 b/g compatible).
Next, temporarily disable your Security setting by changing it "None". Click Update to save the new settings to the Extreme and see if the player can connect to the network that way. If you can, you know that you have a compatible Radio Mode, so the next step will be to find a compatible Security mode.
Return to AirPort Utility again and follow the same steps except change the Security to WEP and see if you can connect that way. If so, that is the setting that you will need to use, although WEP is not nearly as secure as the preferred WPA/WPA2.
Post back on your progress. There are more settings available for Security and Radio Mode in AirPort Utility when you hold down the option key and click on the selection boxes.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
WaterCons, welcome to the discussions!
The likely cause of your connection issue with the Samsung player is a Radio Mode or Security compatibility issue.
Open AirPort Utility, which you used to configure the Extreme, and click on Manual Setup.
Click the Wireless tab just below the row of icons at the top of the pane to display the page for your wireless settings.
Do you know what type of wireless device the Samsung will support? It may not support faster speed "n" networks, so check that the Radio Mode for the network that you are using is set for 802.11n (802.11 b/g compatible).
Next, temporarily disable your Security setting by changing it "None". Click Update to save the new settings to the Extreme and see if the player can connect to the network that way. If you can, you know that you have a compatible Radio Mode, so the next step will be to find a compatible Security mode.
Return to AirPort Utility again and follow the same steps except change the Security to WEP and see if you can connect that way. If so, that is the setting that you will need to use, although WEP is not nearly as secure as the preferred WPA/WPA2.
Post back on your progress. There are more settings available for Security and Radio Mode in AirPort Utility when you hold down the option key and click on the selection boxes.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi there, I'm not a techie at all and I was having some initial difficulty getting the Bluray (I have the BD1250) to work with Airport Extreme but I've got it working now and I thought I'd post my configuration in case it works for any other BD-XXXX models... I'm streaming Netflix and Pandora with no problems and have powered off and on several times...
Airport Extreme:
- I did change my Wireless Network Name to one word (a tip I saw in other forums)
- I'm using WPA2 Personal for Wireless Security
- I'm using my same old password that I've always used
- IPv6 settings were not changed and are currently set at:
a. IPv6 Mode: Tunnel
b. Block incoming IPv6 connections is "checked"
c. Configure IPv6 is set to "automatic"
- under IPv6 Firewall:
a. Allow Teredo tunnels is "checked"
b. Allow incoming IPSec authentication is "checked"
(the IPv6 are all on the Advanced tab)Bluray Setup
Network Selection set to "Wireless"
Wireless Network:
a. I was able to locate my Access Point no problem (using the one-word name)
b. DHCP -- "on"
c. DNS -- "auto"
d. "Save"
Proxy -- set to "off"
NTP Server -- set to "off"After tooling around a bit, what seemed to help the connection was manually entering the Bluray MAC address in Airport Extreme.
- Get the Bluray MAC address:
a. Run the "Network Connection Test", the MAC address for the Bluray should appear on the first line as it attempts to make the connection.
- Add the Bluray MAC address to Airport Extreme:
a. In Airport Utilities on the Airport tab select the "Access" tab
b. Click the "+" sign to add a new MAC address
c. Enter Bluray MAC address and name (I put Bluray for name)I then turned off my Bluray and Updated the Airport Extreme and everything has been working perfectly.
I hope this works for everyone else!
Good luck!
togra
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
The Samsung player DOES support 802.11.n : )
I have the BD-P4600 and it's now working great streaming Netflix and Pandora via my Extreme. I had some initial issues, but worked them out. There is an extensive post over at CNET about others with this issue and I posted my findings there - here's my setup instructions:
Airport Extreme
-Wireless Network Name should be one word, no spaces (mine was, and such a protocol really is industry standard - it is generally accepted that instead of spaces, a user should enter an underscore if desired)
-WPA2 Personal for Wireless Security
-IPv6 settings were not changed and are currently set at "Link-local only" (With this setting, there are no other IPv6 settings or changes required.)
-Set time automatically (This does NOT seem to be "required" but it's on anyway)Bluray Setup
- Set Correct Date and Time. <---If Samsung is unplugged or affected by power failure, this MUST be re-entered for Netflix streaming to function. Good idea to set NTP (time) server ON as well.
-Network selection set to "Wireless"
-Once it discovers your network, choose it. If you have WPA2 Personal security, select the security protocol "WPA2PSK" <---Incorrect choice MIGHT trip up some users out there.
-Enter your normal network password - be aware that there are CAPITAL letters and lower case to choose from...choose appropriately!
-Confirm the following:
a. DHCP - "On"
b. DNS - "Auto"
c. "Save" <---Possibly overlooked by some, important step.
Proxy - set to "Off" - 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Thanks! While I would still argue that this process is neither obvious nor straightforward - and not provided by Samsung - once you have the correct directions it's not so bad.
Thanks again, all.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
For anyone finding this thread later like myself, I just bought a Samsung BD-1950 and had exactly the same problem and Samsung tells me I must get a Wireless LAN adapter from them for the back of the BD player to the tune of $79. MoFo's! I've already spent over $5000 with them!
I'm going to simply wire my router behind the console with a splitter (not what I want to do but going to see if it works ok) and use ethernet to the BD player to see if I can get it going. Later I may buy the wireless adapter if my signal strength seems to weak from using a splitter.
- 0
Apple Support Community member ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
For me, adding the MAC address of the Samsung BD-P4600 to the Airport extreme did the trick.
Thank you for the post.