Benches macOS

5

Xserve (UK) power consumption amps

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Hi,

I am looking at the new Xserve boxes for a new project but the tech specs state an amp drain of 4a. Checking with my datacentre provider they were horrified and said they would doubt it would be over 0.5a. Can anyone clarify the actual power requirements of the latest Xserve as far as a datacentre deployment is concerned?

Thanks everyone.

5 replies

Sign in or join Beachball Help to reply.

  1. 0

    MrHoffman

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    It appears this case warrants another discussion with the data center folks; your question and your confusion here seems to be based on the information and comments you've received from them.

    If you're reading data from the Xserve product specifications, then the rated wattage for most any computer is almost always higher than the actual current usage. The rated wattage from the vendor is the maximum configuration at maximum load with maximum power consumption; it's explicitly and intentionally a worst-case value.

    If you need to know the actual numbers for power consumption for your particular Xserve configuration, then you're going to need to measure that. A DC typically needs to know both inrush and steady-state, and can usually guess at or test for that. Where things get interesting here is when the whole DC powers up, and where all those disks are spinning up. But again, that's for the DC folks to deal with.

  2. 0

    Tim Harris

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    We both supply and host xserves in the UK all the time and never worry about power consumption. They will burn power then they are working flat out - but the chances of that are slim I would say.

  3. 0

    Camelot

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    The power specs on Apple's page and the box are worst-case. They have to report that from a CYA perspective.

    IF your dual 2.93GHz server has three 1TB drives on a RAID card AND an SSD drive AND has fully populated DIMM slots with 4GB DIMMS, AND has used both PCIe slots AND it's in a 90°F environment AND is working flat-out on a CPU-intensive task while simultaneously burning a DVD, it might pull as much as 4amps.

    However, in normal, everyday use it's far more likely to pull around 0.5-1.0 amps

  4. 0

    Antonio Rocco

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi

    I have to agree with Camelot's findings. Hooking up a voltmeter/fluke to the mains and measuring the current never seemed to go above approx 0.6 amps. This was on a G4 (plus CRT Monitor) running OD, DNS, DHCP, Web, Calendar and File Services.

    Tony

  5. 0

    wingnut843

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I am looking at the cooling requirements for a new data center based on the Xserve Early 2009, Dual 2.93GHz Quad Core. The best information I could find was from the Apple efficiency page which references the specpower2008 site and the results are here:

    http://www.spec.org/powerssj2008/results/res2009q2/powerssj2008-20090316-00130.html

    This states that the server consumes 334 W at peak utilization, 173 W active idle. Which at 240V is 1.4A max, 0.72A active idle.

    The test server is maxed out on RAM and CPU but only uses one drive bay. So if I allow for the remaining 2 drive bays to be populated, that is about 13 W per extra bay (1TB typical drive) for a total of 360 W, or 1.5 A at 240V.

    I can't tell you how many times I have seen overblown cooling and electrical systems put in to support power supply rating estimates of equipment.

    So even at full utilization (depends on application) it is only half the nameplate.

    The power supplies are always oversized because inrush/start-up loads (each drive draws about 30W at startup albeit briefly), marketing hype, and limited availablilty of capacies. 500 W might work but is close to peak current, so the next available one they have sitting on the shelf that is hot swappable, load sharing, etc. is 750 W.

    I wish Apple provided better data for their products in all configurations, as they did for previous server lines.

    I hope this helps.