Benches macOS

15

ERROR 306: Canon Pro9000 / Airport Express connection problems in Leopard

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Hi all --

Searched through the discussions a bit and didn't find anyone had gotten any solutions to this yet.

I have a Canon Pro9000 that's connected via USB to an Airport Express base station, which was working fine until I made the switch to Leopard last week. The Airport Utility still recognizes both the base station and the printer, but any attempt to actually print results in an Error 306 (Communications error).

All of the software updates have been run, latest firmware for the base station, latest drivers for the printer. Connecting directly to the printer works fine and, as I mentioned, this all worked perfectly under Tiger.

If anyone has help or suggestions of any kind, would be greatly appreciated.

15 replies

Sign in or join Beachball Help to reply.

  1. 0

    phoenixDownUnder

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    We too have suffered the same problem but it also occurred under Tiger. The problem has not been fixed in Leopard. In summary, any attempt to print a largish document - more than about three pages - via an Airport connection to, in this case a Canon i850 printer, locks up in the middle of an arbitrary page and never completes. Any attempt to restart the print job produces error 306 and any attempt to restart the Airport Base Station also fails. However connecting the printer directly to the computer and printing the same job through the direct USB connection is nearly always successful.

    Thus there is a communications failure I believe within the IP link to the Airport Base Station and if that IP link times out or fails, the whole session collapses. This has been a problem for well over 2 years.

    Printing 1 page at a time via the Airport connected printer works most of the time but if the single page contains a large amount of data - for example a complex image or a Photoshop file, then the the print job always fails. Its repeatable and reproduceable.

    The system we have is an original Airport Base Station with v5.7 firmware, 128 WEP links which are very slow and often fail, connected to a 12Mb WAN connection to the Internet via 10/100 ethernet connection using DHCP rather than a fixed IP address although a fixed IP address connection has been tested with the same results when printing. The Airport unit has a second slave Airport unit connected to allow wireless users further away to print to the same printer.

    A series of macBooks and Pros are used along with a large iron G5 system.

    Interim solution is to bypass the Airport units.

    Cheers,

    Bruce,

    Melbourne.

  2. 0

    waxdart

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    In the event that anyone is watching, I'll bump my own thread by adding that the 10.5.1 upgrade did not solve this problem, sadly.

    Also, per your comments, Bruce -- I only wish I could get a page or two at a time; Mine consistently fails every time with the error 306 prior to
    any print activity. Thanks for your input though.

    I can confirm that the printer does in fact work on its own: printing directly via USB works flawlessly. Additionally, the AirTunes functionality of the AirPort Express works fine as well. Just not the printing part.

  3. 0

    griffdb

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I have the same printer connected to the latest Airport Extreme router.

    I don't even get my first sheet printed.

    Here's what the error log says:

    Friday, November 16, 2007 10:04:31 PM US/Pacific

    I [16/Nov/2007:22:04:34 -0800] [Job 3] Started filter /usr/libexec/cups/filter/pstoappleps (PID 537)

    I [16/Nov/2007:22:04:34 -0800] [Job 3] Started filter /usr/libexec/cups/filter/pstocupsraster (PID 538)

    I [16/Nov/2007:22:04:34 -0800] [Job 3] Started filter /Library/Printers/Canon/BJPrinter/Filters/Raster2CanonIJ/Raster2CanonIJ.bundle/ Contents/MacOS/Raster2CanonIJ (PID 539)

    I [16/Nov/2007:22:04:34 -0800] [Job 3] Started backend /usr/libexec/cups/backend/mdns (PID 540)

    I [16/Nov/2007:22:04:34 -0800] [Job 3] Restarted by "griff".

    E [16/Nov/2007:22:04:41 -0800] [Job 3] Unable to open raster stream - : No such file or directory

    E [16/Nov/2007:22:04:41 -0800] [Job 3] No pages found!

    E [16/Nov/2007:22:04:41 -0800] PID 539 (/Library/Printers/Canon/BJPrinter/Filters/Raster2CanonIJ/Raster2CanonIJ.bundle /Contents/MacOS/Raster2CanonIJ) stopped with status 1!

    I [16/Nov/2007:22:04:41 -0800] Hint: Try setting the LogLevel to "debug" to find out more.

    E [16/Nov/2007:22:04:41 -0800] PID 538 (/usr/libexec/cups/filter/pstocupsraster) crashed on signal 10!

    I [16/Nov/2007:22:04:41 -0800] Hint: Try setting the LogLevel to "debug" to find out more.

    E [16/Nov/2007:22:04:46 -0800] [Job 3] Job stopped due to filter errors.

    Does anyone know how to set the loglevel to debug?

    Thanks.

  4. 0

    Shingo Yura

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I am having the same problem with 10.5 as well as 10.5.1. This problem did not exist when I had Tiger installed. I downloaded the latest driver (10.0.1.0) from Canon site but the 306 A communication error still occurs.

    Can someone please help?

  5. 0

    Shingo Yura

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I just changed my setting on one thing and now my Canon Pro9000 works with the Airport Extreme base station.

    First, remove the printer from the "print&fax" under "system preferences". Then you add a new printer by clicking the "+" sign. When the next window pops up, select the printer. At the very bottom of the screen "print using" field, instead of selecting your printer name, select "canon IJ printer".

    I don't know why but it works for me.

  6. 0

    Mark N

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks so much Shingo Yura.

    I got the error with my Canon iP4200 using a usb cable.

    Adding the printer again in 10.5.1 fixed it.

  7. 0

    Shingo Yura

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    You are welcome. Glad that I can help and it worked for you.

    Shingo (aka David)

  8. 0

    Buey

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I have had similar problems, however, I have had no problem printing with a Canon Pixma iP4000R...I simply cannot access any of the printer utilities. Actually, re-installing the Network Utility doesn't even produce the program in my Applications folder when it says that it is a successful download. After multiple emails back and forth with Canon support, it seems that there is no solution right now. It would be nice to know when an ink level is low which one it is. Through Windows XP in BootCamp I can access the utilities. My computer does freeze on large jobs as well in Leopard.

    Is anyone else able to print but cannot access Utilities?

  9. 0

    griffdb

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Canon posted a new Canon IJ Printer driver on their downloads page for the Pro9000.

    pro9000osxcp10010ej7.dmg

    Pro9000 Printer Driver Ver. 10.0.1.0 (Mac OS X CUPS)

    10.0.1.0 8.35 MB 11/29/2007

    It's on this page:

    http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=DownloadDet ailTabAct&fcategoryid=367&modelid=12892

    Note that you have to select your OS to be Mac OS X for the driver to appear.

    So the combination Shingo-san's suggestion of using the Canon IJ Printer (driver) plus the latest version of that driver enabled me to print via the network for the first time!

  10. 0

    griffdb

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I was remiss in my last post by not saying the following:

    1. You also need this IJ driver from Canon:

    pro9000osx484ej7.dmg

    Pro9000 Printer Driver Ver. 4.8.4 (Mac OS X)

    2. Also, when you have a printer that's connected via airport, you'll never be able to be able to access the printer utilities. You are only able to access the utilities if the printer is directly connected to your computer.

  11. 0

    gakon

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I was having some similar problems with an Epson Stylus Photo 960 (started to print, then got bogged down and had a communication error). I decided to search on Apple's support page (I had come to the discussions pages first). I performed the steps outlined in the link below, and it seems to have fixed the problem for me. Not sure if it's going to last, but we'll see. The last few steps are for older versions of OS X (not 10.5), but it's pretty easy to figure out what to do.

    http://docs.info.apple.com/article.html?artnum=107418

  12. 0

    cpurrin1

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Removing printer from list of printers, then re-adding ... did the trick for me, too. Thanks.

  13. 0

    IdeaGeo

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Waxdart,

    I share your frustration. The Canon Pro9000 via direct USB works great, but when I try to run it wireless to my Airport Express I have recognition of it's presence but it doesn't work. I've been running a Canon iP4300 off of the same Airport/USB with no issues for months, even across the Leopard upgrade and figured the 'Pro9000' would work as seamless. Not the case. Looks like we're going to have to wait for Apple to update software or splice a bunch of USB cables together to cover the distance 🙂

    -G

  14. 0

    gakon

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Well, this doesn't work consistently for me. Every so often it loses the connection or whatever, and I have to re-perform these steps. I'm going to try the AirPrintFix mentioned in another thread.

  15. 0

    gakon

    Imported from the Apple Support Forums via the Wayback Machine 🔗