cannot start up: circle with slash throu…
apple Verified ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I could not start up my computer: I get a circle with a slash through it (don't know the name of the symbol)
Tried restoring previous versions through time machine: one just before problem and one 2 hours before problem, but after restore same problem: whirring wheel for startup, then circle with slash. Now I am trying to restore from time machine backup from previous day. Awaiting results. Is there something more serious? How far back should I go?
15 replies
Sign in or join Beachball Help to reply.
- 0
otobinchicago ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
i thought the problem was my computer, but I have tried these backups with another (newer) computer.
- 0
macjack ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
This support topic can help:
http://support.apple.com/kb/TS1892
Do any of these situations apply to you? - 0
otobinchicago ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I am now reinstalling the new system as the support topic suggested. If that works, and it probably should, is it proper to then reinstall the applications and documents
- 0
macjack ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
- 0
Steven Hopstaken ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I am having this same problem. Holding down the shift key and restarting into safe mode, then restarting again fixes the problem temporarily, but after a few restarts the circle with slash thorough it (the no entry symbol) comes back.
Other discussion boards have two theories, 1. it's a firewire event call problem (most people with this problem have a firewire drive connected). The 10.2.6 update was supposed to fix the problem, but it hasn't.
Or 2. it is a bad NVRAM chip on the motherboard. Several people have taken their Macs in for service and had the motherboard replaced and it has fixed the problem.
Oddly enough, I have Windows 7 installed on the iMac and it boots every time, even when I'm getting the No-Entry symbol on the Snow Leopard start up.
I'm going to do a complete erase and reinstall and see if that fixes the problem, but if it doesn't the iMac is going back for a refund. I've lost days of work dealing with the problem! Time to think about a Windows 7 machine.
- 0
ChrisdeG ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi,
I'm having the same "circle with line through it" issue. I did a clean install from Snow Leopard, then used my time machine backup to bring back all of my files. Unfortunately, the problem has returned as well. I can use Safe Boot to log in, and Disk Utility claims that there are no problems with my drive. After using Safe Boot I can restart my computer normally a couple of times, but then the problem returns. Is is possible that by restoring all my files I brought back something that is causing this problem? Or is a hardware problem more likely?
Thanks!
- 0
Meherally ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Hi
Very likely hardware issue. Seems to me the system not able to get past the initial hardware check. Suggest run the Apple Hardware test. It should be on a CD that came with your Mac. If you cannot run that, just get it checked by the store where you purchased. Seems to me a RAM problem. - 0
ChrisdeG ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Thanks for the advice- I just went through both the short and long hardware tests. No problems were detected by either one, but I think I'm just going to take it in for service. I'm out of ideas.
- 0
nickelman03 ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
What did the Apple Store tell you when you brought it in? My Early 2009 Mac Mini is doing exactly what yours is. The problem I have though is that I replaced the HDD and RAM myself which i've been told voids my warranty.
Thanks...
- 0
CJ Crucke ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I just got this problem today - what did the apple store do?
Thanks!
- 0
Panayotis Kammenos ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I have exactly the same problem since approximately 2-3 weeks.
Booting with Shift (Safe Boot) and then rebooting normally temporary solves the problem (no need to reset NVRAM).
Any help welcome... I do not believe in the theory of hardware problem... Too many similar cases in the last days! - 0
celticpride678 ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I had this the first day with my Mac. For me, the issue was a failed hard drive. Went back the next day and got the Mac replaced.
- 0
Panayotis Kammenos ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Nothing to do with drive hardware I have the problem both with the internal drive and an external bootable usb drive created with Super Duper
My observation is that the problem comes back after Shutdown. Starting with Shift Taste (Safe Boot) and doing a restart after this safe boot start works normally. Further restarts too. If I use Shutdown, I find the problem again on the next start. Anybody knows what the system does during shutdown? - 0
Panayotis Kammenos ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Problem solved using Snow Leopard Cache Cleaner (medium cleaning of System Cache).
To sucessfully run sLCC, start Mac in Safe Boot mode
Run sLCC - the system restarts...... Done! - 0
folks ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
after sLLC process recommended above: shutdown and startup work less than ten times before the problem emerges again. This problem showed after extended hardware test, disk repair, repair file permissions, update to 10.6 and online update to current 10.6.2 from fully updated 10.5.8
Startup in safe mode then restart works. Shut down appears to be required to setup the problem.
An thoughts are welcome.