iMac G3 Display Popping Noise
apple Verified ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
My iMac G3 makes random popping noises coming from the screen and a black stripe appears for a fraction of a second while this happens. Is this bad? I had to unplug and plug in the computer several times as I was having boot issues and it stalled. Could I have damaged the CRT neck? Or is static electricity just jumping between some dust? What should I do, as right now I have it unplugged.
7 replies
Sign in or join Beachball Help to reply.
- 0
Kenichi Watanabe ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Yes, that is usually a bad sign. There is a part on the analog video board that provides the high voltage needed to drive a CRT display. It is called the flyback transformer. When it starts to fail, you will have that symptom with the electrical popping sounds. Your iMac may also start to shut off unexpectedly, by itself. In order to restart it, you need will need to unplug from power it for a few minutes. This will get worse until the iMac is no longer able to pass the startup hardware self-test, so it is not able to complete startup. This is the most common failure point for CRT iMacs and it is not an economical fix for most people.
Is it a tray-loader or slot-loader? If it is a tray-loader, there is a test you can do to comfirm if it is this problem (or something else) on the analog video board.
Edit: Oh, I see that the iMac in your profile is a tray-loader. Is that the iMac with this problem?
- 0
Super TWiT ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
It is the one thats having problems. The boot issues were with linux though (yaboot) and weren't due to hardware fault. It usually happens after it has been left on awhile so I am thinking it may be a dust issue with static electricity build up. Also, the stripe always appears in the same spot. I am going to try blowing it out with a can of compressed air.
- 0
Kenichi Watanabe ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
An electrical pop accompanied by some visual artifact on the screen is probably not dust accumulation. If you later experience the symptom of the iMac not getting passed the initial power-on hardware self-test, you can check to see if it is an analog video board problem by doing the following on tray-loader iMacs.
Open the bottom panel. Disconnect the internal video cable that goes between the chassis (the thing you pull out) and the rest of the iMac. The video cable is the one that looks like a video cable, with the twist-on fasteners. Leave the other cables connected.
Try to start it up. Obviously, there will be nothing on the screen, but if you can tell that the iMac is otherwise starting up normally based on the sounds it is making, then the problem is probably the analog video board. By disconnecting the video, you bypassed the problem and the iMac is able to pass the hardware self-test.
You can shut down normally without video by pressing the power button and then the Return key.
- 0
Super TWiT ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
After blowing it out I still has the problem, it seems to be the flyback transformer. Is there anything I can to do to extend its life other than turning down the brightness? Also, is it damaging to the computer if I continued to use it?
- 0
Kenichi Watanabe ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I don't think there are any preventative measures. If you opened it up to far enough to remove dust under the plastic cover, that may help by keeping it cooler.
Ultimately, you can bypass the iMac's video sub-system and connect that internal video port (on the pull-out chassis) to a VGA monitor. You need an adapter that looks like this one
[Apple video to VGA adapter on eBay|http://cgi.ebay.com/New-Switchable-Apple-Mac-to-VGA-Video-Adapter-TVCS-183
W0QQitemZ360174533722QQcategoryZ41993QQcmdZViewItemQQ_trksidZp4340.m183QQ_trkpar msZalgo%3DSICDD%26its%3DI%252BC%252BS%252BIA%26itu%3DSI%252BUS-BWR%252BUCI%252BI A%252BUCC%252BPSS%252BCRS%252BIT%252BUA%26otn%3D6%26ps%3D33#ht_26305wt1111]It has one switch that you set to
VGA/G3. Interestingly, when connected this way, you can get resolutions above what the internal display is capable of using, up to 1600x1200 if the external display is large enough to support it. The original 233 MHz iMacs only had 2mb of VRAM (upgradable); the later tray-loaders had 6mb. It probably needs 6mb VRAM to go up to 1600x1200.The video on my tray-loader failed a long time ago. I even bought a replacement analog video board, but unfortunately, it was a salvage part from an eBay seller and if failed about six months later. Since I had invested in some cool upgrades for it, I removed the computing parts from the case and use it connected to a nice VGA display, usually at 1280x960 (millions of colors). So, in terms of functionality, it works better now after the video failed on it.
- 0
Timothy Fink ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
I have a Rev A Bondi Blue G3 iMac that just started making sparking noises and flickering the display. I know it is just something that runs that, because it doesn't affect the OS function at all. Thia CRT has lost its red somewhat years ago.
I have a Harmoni upgrade card in it, extra video RAM (6MB). I wonder if I can move all this over to a Strawberry Rec B or C iMac I also have?
- 0
Kenichi Watanabe ·
Imported from the Apple Support Forums via the Wayback Machine 🔗
Yes, the parts should be interchangeable between Rev. A through D, at least for the user accessible parts. Some of the parts that are +further in+ such as the analog video board are slightly different.
But you can move the RAM, the CPU card (or Harmoni upgrade card), and the hard drive between the tray-loader revisions. You don't need to move the video RAM, because the Strawberry Rev. C already has 6mb. In fact, you should be able to pull out the whole
chassis from the Rev. A and swap it with the chassis in the Rev. C. However,the Rev. C motherboard should have slightly better ATI graphics hardware, compared to the original Rev. A. So you may want to keep swap the individual components instead.Two things the Rev. A and B have that C and D do not have are the infrared sensor and the "Mezzanine" slot on the back side of the motherboard (sort of a modified PCI slot). However, almost nothing used those features, so it should not be a big deal.