Benches Mac desktops

11

Tray-loading iMac won't install Panther. …

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I just put in a 40GB IDE Hard Drive in a tray-loading iMac that I acquired today because I couldn't do a whole lot with 6GB. The only trouble now is it won't install OS X 10.3 Panther and shows a message saying the "destination is not within the first 8GB of the disk". I tried repartitioning my 40GB hard drive into 2 partitions one 7.7GB and the other 27.3GB. But it wouldn't even let me install it on the 7.7GB partition. What am I doing wrong?

266 MHz PowerPC G3

256 MB PC66 RAM

24x CD-ROM

The only way I can use this computer is if I boot from the original OS 8.5 restore CD.

11 replies

Sign in or join Beachball Help to reply.

  1. 0

    Kenichi Watanabe

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    7.7GB is
    right at the limit of what the Installer considers to be 8GB. Try 7.5GB; it should work.

    Also, make sure you set the jumpers on the hard drive to +Master (single drive)+. On the tray-loader iMac G3, the CDROM drive has a separate IDE bus, so the hard drive is the only drive on its IDE bus. Some drives only have one
    Master setting.

    Tip: When you run Installer, go into the Customize screen and de-select all the printer drivers, languages, and applications you do not need. That can save you up to 1GB of space, and that's a big deal when you only have 8GB (or 7.5GB) to work with on the startup volume.

  2. 0

    Jrtechn

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I set the jump to a single master and that seemed to only make things worse because it would no longer boot into the Panther install CD. In the meantime I guess I'll try the smaller partition.

  3. 0

    Tony Da Silva

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi, Ken - Would Open Firmware update be at issue? I ask only because...

    The only way I can use this computer is if I boot from the original OS 8.5 restore CD.

    ( I don't have the answer, the quote from OP jumped out @ me.)

    ::tonyd::

  4. 0

    Jeff

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Reset the jumper as "master" or "master w/slave present," not "master/single"

  5. 0

    Kenichi Watanabe

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    For a tray-loader iMac G3, it should be Master-single (or Master if there is not distinction). The hard drive and the optical drive each have their own IDE bus. For a slot-loader iMac G3, it should be +Master w/ slave drive+, because the hard drive and optical drive share the same IDE bus.

  6. 0

    Kenichi Watanabe

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Good point. Although it appears the iMac is able to boot the Panther CD based on...

    The only trouble now is it won't install OS X 10.3 Panther and shows a message saying the "destination is not within the first 8GB of the disk".

    That's all the way into Installer.

    However, take a look at this list

    http://support.apple.com/kb/HT2560

    Under +266 MHz iMac+, there is a list of firmware updates, the most important one being +iMac Firmware Update 1.2+.

    If you don't know if these firmware updates were installed, you might want to install Mac OS 8.5 on it first. Then try to run those firmware updates. If they are already installed, the installer will tell you; no harm done.

    Then, try starting up from the
    Panther Disc 1 CD again. You can run Disk Utility from the Installer's
    Installer menu (at the first screen go up to the menu bar), and reformat (erase) the internal drive. Then quit Disk Utility and go back to Installer to proceed (hopefully) with the installation.

  7. 0

    Jeff

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I've only come across the designated "Single" jumper setting for Western Digital drives. For the others (Maxtor, Seagate, Quantum, etc.), the Master or Master w/Slave setting seems to be more common. I only suggested switching back to either of the latter settings, because he's now unable to boot from the optical drive. If he has a WD drive, perhaps he has incorrectly placed the "Single" jumpers, as there are differences between the 6-pin, 9-pin, and 10-pin WD jumper blocks. For the 6-pin and 10-pin blocks, no jumper is installed for "Single," whereas a pair of jumpers are installed on the 9-pin block to configure it as "Single."

  8. 0

    Kenichi Watanabe

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I'm not sure what's going on with not being able to boot from the optical drive. Technically, since the optical drive is on a separate IDE bus from the hard drive, the settings on the hard drive should not affect the optical drive (unless a setting that was changed has some other effect that prevents booting from any device - not master/slave related). Definitely a good idea to check the jumper settings to makes sure the proper pins are being jumped.

  9. 0

    Jrtechn

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    UPDATE: Last night I set the jumper to cable select. It is a Western Digital HDD. When I did it let me install Panther onto it. But once I ejected the Panther install CD and tried to make it boot to the 7.5GB Hard drive partition with panther on it. I got the typical flashing folder icon indicating no OS. I'll try setting it onto master w/slave present. Even though there is no slave since the optical drive is on a separate IDE bus.

  10. 0

    Jrtechn

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I attempted to update the firmware.

    1. took the 40GB HDD that I'm trying to install Panther on and put it my Power Mac G4 (which already has Tiger installed on a 120GB Hard drive).

    2. Downloaded the 1.2 Firmware update and then copied it onto the 40GB hard drive.

    3. Put the 40GB hard drive back in the iMac and booted the iMac from the OS 8.5 restore CD and opened the firmware update from there.

    4. Got a message saying "Your iMac's firmware is up to date"

  11. 0

    RmblnJoe

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I recently updated a tray-loading iMac to OS 10.3.9. I took a 40 GB HD from a dead iMac slot-loading and placed it in the tray loading machine. I forgot to reset the jumpers. I started up from the install CD, partitioned the HD with the first partition of 7.5 GB, and installed the OS just fine. I re-started the computer, popped out the install CD and got the flashing folder. I panicked. Then I remembered the jumpers on the HD. I pulled the HD back out, reset the jumpers to master as shown on the HD, put it back in and it started right up!

    Hopefully that is all you need to do.

    joe