Benches Mac desktops

10

Overloading My APC UPS XS 1500 whilst sleeping

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

New to the MacPro world (my dual G5 regretfully suffered an early demise) and I'm experiencing the problem mentioned in the subject, i.e., while my MacPro is sleeping (and generally many hours after going to sleep) the Overload red light while come on and the unit will start beeping. I saw references to a very long thread on MacPro's and UPS problems while searching this topic but did not find the actual thread.

I have an APC Back-UPS XS1500. Have my MacPro, 23" monitor, DSL modem, Netgear router and small JVC stereo running on it, which worked with the Dual G5. After the overload cannot bring the MacPro back from sleep.

Is there a sleep setting I'm missing on the MacPro. Or do I need to acquire a bigger/second UPS for the MacPro?

Grateful for all help and suggestions.

10 replies

Sign in or join Beachball Help to reply.

  1. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    I have had the same problem. I spoke with APC and the unit will support more than what either of us have plugged in to it. Mine only does the overload problem when it is sleeping. On a few occasions it has gone to battery power briefly while there was still power. They said it could be a fault in the unit. I wish APC had an answer.

  2. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    We talked about this over the last year, more last fall, Wake from sleep load is extreme. The RS1500 is better. I use the RS for Mac Pro and everything else on XS1500. Or the SMART 1500VA is safe.

    Make sure you aren't sharing that line circuit with other equipment.

  3. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    What is the normal amp draw on start or wake? I have a new Mac Pro dual core running stock (no pci cards, extra memory etc) and it's pulling down almost 10 amps at startup and wakeup. Is this within normal range? I had it plugged into a Furman 1500w power conditioner which was then plugged into an older APC 1100. The Furman was straining so I bypassed it directly to the APC Which seems to handle it OK for now(will be adding stuff), but it still pulls 10 amps which seems like an awful lot.

  4. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Had seen your other post on this, wasn't sure if it was the final solution and it will present space issues. Oddly enough, like scotthopkinsphoto, mine is going into the overload while it is sleeping, not upon awakening it, although I guess something else might have triggered a wake-up or the APC may have triggered a test.

    Thanks for the response, will do a little shopping today.

  5. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Really don't have any idea how much it is drawing at startup, and oddly the problem is while it is asleep. Current workaround is setting it not to sleep.

  6. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    The older 1100 is "under powered" a bit. I would also reverse the setup:

    wall -> line conditioner -> UPS -> Mac Pro

    Suggestion: use the 1100 for monitors and such, make sure your wiring and current is okay and not shared with other equipment, and get RS1500 ($209 Amazon) for just the Mac Pro.

    There was a thread and some input from emails with APC and others on the subject.

    The 'wake from sleep issue' is as much about the PSU Apple still seems to use as anything. Go ahead and add RAM (10W for each FMDIMM?) and hard drives and controllers (300W max).

  7. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    You guys are fast! Thanks, I will follow your advice and upgrade my APC before adding to the system. However, my main concern at this point is whether the high amp draw is an indicator of a possible problem(or potential future problem) with my computer itself or if this is the norm for these beasts. It seems from what you guys are saying, that they do draw a lot. I will see if I can find someone in my area that would let me measure the draw on their machine. Unfortunately, the place where I got mine, deals on an order only basis and doesn't have any on the floor to test. I will report back if I'm successful. Just in-case anyone out there is interested, I used a cheap Radio Shack clamp-on(inductive) amp meter and a modified extention cord(wires separated so you can clamp around a single wire). This is totally non invasive if anyone wants to try it.

  8. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Kill-A-Watt is helpful.

    I had someone come out and run a new circuit to my "office" so I am on dedicated line. But having a real electrician come out can be worth the $50-100.

    Apple Support page for Mac Pro has a link to BTU requirements.

  9. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Got my RS 1500, charged it, placed the computer and monitor on it, everything else on the XS 1500. Put the computer to sleep, woke it up, no problems.

    Thanks for the assistance.

  10. 0

    Apple Support Community member

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Awesome! glad it is working the way it should.

    Either those K-A-Watt units aren't accurate, or APCs PowerChute under Windows (really detailed) is off but my system shows just the system draws 260W with 2GHz + 4 drives + 6GB RAM. Not doing much more than doing a backup and browsing.