Benches Mac desktops

4

Fixing iMac(CRT) firmware/OS X problems

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

b I didn’t
update the firmware on my iMac before trying to install OS X 10.2 or higher on a slot-loading iMac. How do I fix resultant bootup or screen problems?

b Introduction

This topic is a summary of a fuller article which can be found
here. It does not apply to tray-loaders but only to slot-loaders.
How to differentiate between models

The latest firmware for slot-loading iMacs is
4.1.9. If OS X goes anywhere near an iMac with an earlier version then often peculiar screen problems are caused, or the iMac won’t start properly. In most cases it is possible to fix these problems. This topic explains how to do so.

All users who have installed OS X on a slot-loading iMac should make sure that their firmware is at version 4.1.9. Even if the iMac is working at the moment, problems may arise at any time.

If you are having problems then

b do not reset the PRAM

until the firmware is updated, as doing so can make the problems much worse.

To fix the problem you simply need to update the firmware. If your iMac is not behaving properly this can be a little tiresome, but usually not impossible.

b Symptoms

The symptoms are well known and many users have experienced and overcome them:

* S0: OS X installation attempt fails; there may be a message “you need to update the firmware”; the iMac freezes (often with a grey screen); the CD is stuck in the drive

* S1: the iMac starts up but the screen is blank

* S2: the iMac starts up but the screen is dark and a strange colour

* S3: on power on or a restart, the green light comes on but nothing else happens

* S4: after the startup chime the iMac turns itself off after 7 – 10 seconds

b Overcoming the symptoms

i S0: To get the CD out,

find the emergency eject button inside the right-hand end of the CD slot. Hold it in with a paperclip during power-on. (NB this then disables the CD drive till next power-off.)

i To get round S3,

remove the power cord between reboots.

i To get round S1,

after the iMac has booted, briefly press the main power button to send the iMac to sleep. Wait for the button to pulse orange, then press any key on the keyboard. Usually you will now have symptom S2.

i If you have S2 or S1

and a 400 MHz iMac or later, there may be a VGA connector under a small panel close to the memory access panel on the back of the iMac. Many PC monitors will work if plugged in here.

i If you have S4

then check the suggestions in the
full problem solver.

b Upgrading the firmware

The firmware resides on the logic board in non-volatile RAM. To install the latest version (
4.1.9) and hence fix the iMac’s problems, you first need to boot OS 9.1, or 9.2.x from a local HD. If you have 9.0.x then you can
download the 9.1 update from the Apple site.

Make sure you follow all the installation instructions carefully.

Once the firmware is installed (but not before), it is often worth doing an additional PRAM reset: on startup, hold down Apl-Opt-P-R and wait for the second chime.

The most stable version of OS 9 is 9.2.2, so now download and install these updates:
9.2.1 and
9.2.2.

If you need further help then contact Apple Support, check out the full problem solver, or post a new topic in the
Apple Discussions iMac(CRT) Usage forum.

Thanks to all contributors.

4 replies

Sign in or join Beachball Help to reply.

  1. 0

    Kyle Koerner

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Giles,

    If OS X goes anywhere near an iMac with an earlier version then often peculiar screen problems are caused, or the iMac won’t start properly.

    You may also want to mention that newer disk utilities such as DiskWarrior can make the iMac boot into Mac OS X, and cause this problem. There have also been a few instances where a user did not believe it was the firmware because they did not install Mac OS X, only boot from it.

    (NB this then disables the CD drive till next power-off.)

    Could you please fill me in - what does NB stand for?

    You may also want to include some sort of disclaimer, that the problem can vary, and is not guaranteed to work for everyone, etc.

    Its excellent overall. And, you're not even a full Mac user, which has to make things harder.

    Kyle-

  2. 0

    Giles

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks Kyle

    re. Diskwarrior etc, I'm at about 3,990 chars but I'll see if I can squeeze sthg in!

    NB = Nota bene = Note the following

    No space for proper disclaimer ... the topic does point users to the full text for further advice where these points are picked up more fully.

    If you read carefully you will see I have made judicious use of words/phrases like "often", "in most cases it is possible to fix" etc.! so I think your point already taken care of.

    "And, you're not even a full Mac user, which has to make things harder." Correction. I'm not a Mac user. I like to think this gives me a certain independent perspective!!!

    Cheers

    Giles

  3. 0

    Giles

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    The final text is at reply #2.

    I suggest it be moved to the iMac(CRT) tips folder.

    As quite a large number of visitors to Discussions continue to have this problem (in excess of 1 a day I would estimate), I also suggest/request

    * links to the tip are posted in the OS X 10.2 and 10.3 User Tips folders, and

    * sticky links are posted in the iMac(CRT) Usage and Displays folders

    I would be happy to post the full problem solver as a User Tip but this is not straightforward in view of the 4K limit on message size.

    Regards

    Giles Kennedy

  4. 0

    Kyle Koerner

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Nice work Giles. Again, thanks for all of the hard work from you and others. We all appreciate it.

    Kyle-