Benches Displays

4

External monitor resolution stuck out of range

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I have an original 15" macbook pro, and a 24" external monitor which I had been using successfully for some time. Recently, when I connected the monitor as I usually did, it worked, but the resolution was much less than usual. When I went to correct this issue using the `System Preferences > Displays` I chose the wrong option by mistake (I believe I chose the wrong hertz rate but cannot recall, it was accidental). The monitor went black, and now displays a monitor error saying the signal is out of range.

The resolution has not defaulted back to the one that works, and now all attempts to connect the monitor results in this error. I've tried disconnecting/reconnecting the monitor, restarting the computer, clearing the PRAM, and deleting the com.apple.windowserver.plist and com.apple.prefrences.displays.plist files to no avail. I cannot get the resolution set back!

Any help would be useful.

4 replies

Sign in or join Beachball Help to reply.

  1. 0

    den.thed

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hello Bellardia

    Welcome to Apple Discussions

    Reconnect the Monitor and open System Preferences > Displays, then on the Mac's preference panel hit the Gather Windows button. You should now see the preference panel for the Monitor labeled "NTSC/PAL" or something like that behind the Mac's preference panel. Click on the top of it and bring it to the front, then select the proper Resolution: and Refresh rate: for the Monitor. Try the closest Resolution to 1920 x 1200 you have and 52 Hertz or the highest setting for the refresh rate.

    Dennis

  2. 0

    K Shaffer

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Have you left the monitor unplugged from the computer and

    from power for some time, to see if by some chance there is

    a built-in default range the display would re-set itself back to?

    Some persons suggested a startup without the defective

    display attached, and plug it in after the computer's OS

    has settled down and the drive stopped working; to see

    if the re-boot, absent this display, would clear the system.

    (leaving the display unplugged a day may help, too.)

    There's a page full of similarities here...

    ' Mac display resolution stuck out of range ' - google search:

    http://www.google.com/#hl=en&source=hp&q=Macdisplay+resolution+stuck+out+of+range&btnG=Google+Search&aq=f&aqi=&oq=Mac+displa y+resolution+stuck+out+ofrange&fp=2cca7b2e99206b9c

    In earlier times, one could attempt to manually adjust the

    display by use of buttons on it, and those settings would

    stick at least until the next time the display was detached

    from a computer, and/or the power was removed awhile.

    But with modern hardware, getting the display to reset to

    whatever defaults (within range of the computer) should

    be easier than back in the stone age of cave drawings.

    Something similar to this process should be available for

    your computer to use a larger external display again:

    mac mini: troubleshooting "out of range' alert message

    http://support.apple.com/kb/TS2213

    In any event...

    Good luck & happy computing! 🙂

  3. 0

    Bellardia

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thanks a lot for the tip. Originally I couldn't see the window because it appeared on the other (black) monitor, but using spaces I was able to drag it over to the working one.

    Now there's still a small issue of the available resolutions to choose from. For some reason 1920x1200 only has 76 and 85 Hz rates available, while most of the others resolutions have 60,75,80, 90 available. My monitor only supports up to 60 and I'm sure I had it on 1920x1200 @ 60 at some point.

    Is there any way to force it to a non listed resolution?

    Thanks for the help!

  4. 0

    Izaaner

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi, not sure if this will help anyone but

    if there is a display issue with a mac monitor (black screen and resolution set to the lowest with no way to change anything in the monitor system utility) it may be due to a false power start with the monitor plugged in to the mac at a bad time. I think the monitor has some of the display settings set in itself, try unplugging the monitor (from mac and unplug power) and replugging after a few seconds. Then try plugging the monitor into the mac after it has fully booted.

    note: this worked for my 24" mac laptop monitor.