Benches Displays

2

broken stand

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

Hi, i have a 22" flat-screen Cinema HD Display, the bulky plastic encased type, not the aluminum ones.

I was transporting it recently and the stand leg ont he back snapped off at the metal part,

i had a look and it appears to have a kind of spring on the hinge which held it tight, this spring has now forced the small remaining part of metal down so i cant re-attach it with any kind of superglue (a dodgy idea anyway i know!), and there isn't enough there to grip onto to pull with the strength of the spring..

i tried partially dismantling it and the whole stand and hinge are screwed onto the back, I'm thinking my only option is to replace this entire part, where would i get such a part? or if i cant is there any other option as for the moment i just have it propped up with a heavy box which is risky and not ideal for desk space or appearance!

Cheers

2 replies

Sign in or join Beachball Help to reply.

  1. 0

    pat hughes

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    OK, this a much too common issue with them broken stands. Thousands have broken and they cost an arm and a leg ( no pun intended ) to replace or repair, Mine broke off just by adjusting the angle a bit. What I did and I will put it on youtube if I get some time to do it, is to screw the plastic stand on the back of the clear enclosure. You will only lose the tilt function but it will be tilted in a comfortable 15 degree.Simple, elegant, neat, permanent, no glue'and best of all will never break under normal circumstances and you can easily dissassemble it for packaging.Interested ? read on.You don't even have to take off the broken piece on the monitor but you have to take it out from the foot. You will need a drill with a 3/16 and a 1/4 inch bit ( for metal), 2 screws that will fit snugly or slightly larger than the 2 holes of 3/16 you are gonna make with the drill, these screws are philips or whatever but what is important is that they are 1-1/2(one and a half ) inch long with a point and have to fit into a 1/4 inch hole and have a flat and wide head as possible.OK the first step is to drill 2 holes of 3/16 inch on the plastic foot in the cavity where the broken piece used to be. ( you did remove it didn't you? If you look directly in the cavity you will see that it is about 3 inches long and about a half inch high. The trick is to drill 2 holes 3/16 into the cavity at 1-1/4( one and a quarter inch) apart ( doesn't have to be exact but the idea is to make 2 holes within the cavity that are at least 3/4 inch apart. Now comes the part that you have to remove the back cover. That 22 inch model has a metal lining attached to the back cover but it is not necessary to remove it.Now measure the distance between the 2 holes (center to center) you have made in the cavity. Now just above the rectangle opening on the back cover where the foot used to be and about 1/2 inch from the top of it ( metal side) mark with a pencil the drill marks spaced the same distance apart as the foot holes. Make sure that the 2 marks are 1/2 inch ABOVE the opening and centered. Now comes the drilling of the 2 holes in the metal-plastic. From the Backside (metal side) use the 1/4 drill bit and make the holes as straight down as possible. ( A metal 1/4 bit is needed). All is done. Take the 2 screws and fit them from the back side while holding the foot, tighten them into the foot. Done. Put everything back together and Voila. When later you do come across a metal hinge insert, all you have to do is remove the 2 screws and your monitor will be back as new.

  2. 0

    greymattergroup

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    This is something I just replaced on my broken 22" Cinema Display. It's pretty straightforward.

    The spring/bracket is referred to as Apple part ID: 922-5670. They seem to be less common to come by now, and sell for as much as $130 each (I know, ouch). I was lucky enough to find one on eBay for $40. BE CAREFUL that you are sure to buy the part for the 22" display. I've seen some on eBay that were for other size displays. I assume these won't work.

    Once you have your bracket, it's just a matter of disassembling the display.

    You'll need:

    - 5/64 Hex Key Allen Wrench

    - Phillips head screwdriver

    - (optional) something like Silly Putty to help pull out loosened screws from the holes in back of display.

    There are 18 screws on the back of the display (and 3 in the back leg stand).

    1.) Lay the display face down on a blanket, with the top edge facing towards you, on pile of soft cloths (to protect from scratching)

    2.) Remove the screws from the display back (using the putty to help pull out loosened screws from the deeper holes.

    3.) After removing the screws from the display, slowly pry the back piece up, being careful not to go too far as there might be a cord connecting the "guts" to the status lights (depending on the model). If that cord exists, just separate it by pulling gently on the white connectors. Now you can stand the back up and out of the way.

    4.) What I did was just replace the part of the bracket the holds the spring element. That larger metal brackets seemed to be glued on (besides being screwed down) and wouldn't budge for me.

    It's easier to remove the plastic piece covering the spring. The side end caps come off with a little pressure, and then the rest of the covering should come apart on its own. This will let you remove the 4 screws holding the spring unit on. Swap this out and then replace the plastic covering piece -- being careful to note how the end cap pieces align with the tiny grooves. They should just slide on VERY easily. If you have to force them, you're not lined up with the grooves.

    Before replace the back cover, make sure to reconnect the status light cable if you had to disconnect it earlier.

    Then position the back down -- making sure the bottom "legs" snap together. Then just tighten the screws back in. Tighten with a fair amount of force, but don't overdo it or you might crack the plastic. 😟

    Lastly, put the back leg on again. Make sure to add the clear cylinder-like plastic piece that goes over the silver hinge/bracket piece BEFORE you reattach the back leg again.

    Hopefully that helps. Let me know if you have any questions.