Benches Apps and software

6

Canon XL-H1 will not connect to Mac

apple Verified

Imported from the Apple Support Forums via the Wayback Machine 🔗

I typically don't post a question because I continue dig until I find a solution, but this one has been a stumper for me. Here are the details, all scenarios included to minimize suggestions I've already attempted.

I have been shooting and capturing 1080i footage from my Canon XL-H1 for about 8 months now. Last week I went to capture once again and when I started FCP it said I needed to connect my device. Double checked and indeed it was connect, turned on and set to HDV. No settings had been changed since the last capture. So here's what I've attempted.

Check to see if Firewire port is the issue? NO both an external HD and another camcorder can connect.

Check to see if the Firewire cord is the issue? NO cable worked fine with a different camcorder.

Does System Profiler see the XL-H1? NO. I know at the very least it should say UNKOWN.

Is it a Final Cut Capture setting issue? NO. My capture presets are Apple HDV 1080i Firewire Basic (as suggested by Apple).

Will it connect with other Apps? NO. iMovie 09 and Quicktime do not see the device.

Ah-Ha, so it must be the camcorder that is the issue? NO. I went to another Mac and I was able to capture no problem.

Did you search google for answers?
sigh

So here is the million dollar question, that I hope to be answered for free. What could have changed on my computer to make it not work? Are there some hidden files I don't know about that allow a Mac to recognize the camera? Kinda like a driver or something.

HELP, please.

6 replies

Sign in or join Beachball Help to reply.

  1. 0

    Donnymac

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    You most likely tried this but here it goes anyway.

    With your camcorder and cable dissconnected; fire-up your mac and then FC.

    Start a project with sequence settings to match your capture settings.

    Quit FC and shut down.

    Connect your camcorder and turn it on.

    Fire-up your mac and start FC.

    Go to log and transfer - capture now.

    Good luck!

  2. 0

    pmildren

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Thank you for suggestion. I have tried multiple turn on and turn off of computer and camcorder. It appears as if the computer doesn't even see it. I should at least be able to have the camera connected in 16:9 DV Record mode and have something like iMovie or Quicktime see it, but neither of those do.

  3. 0

    gogiangigo

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Hi,

    Disconnect any external FW device, including your external HDs then try again.

    Luca

  4. 0

    pmildren

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Yep, I have attempted it without any external HD including changing my scratch disk to a secondary internal HD.

  5. 0

    pmildren

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Also, for those of you familiar with the XL-H1, I wanted to mention some settings I have tried out on the camera. One thing I have continued to read about, in my google search, was the down convert setting as well as the camera's fuse.

    I have made sure that the down convert was turned off. I also tested to see if the signal settings might make a difference. I have tried each of the Auto, manual HDV and DV settings and non have made a difference.

    Just to confirm that my firewire is fine and its something that has changed within my hard drive, I am going to switch the OS HD with an older one that had Final Cut installed on it. I'll let you know the results.

  6. 0

    Studio X

    Imported from the Apple Support Forums via the Wayback Machine 🔗

    Not sure how the canon handles settings switching but in other cams you have to have the camera unplugged from the firewire cord before the camera will actually change the settings. It may LOOK like the settings change but they don't.

    x